Having problems with your Kirby G5 Bagged Upright Vacuum ?

My Kirby G5 will not start. Head not aligned?

\015 My Kirby G5 will not start. Someone said the head is out of alignment and the safety feature will not allow it to come on. I do not have an instruction manual to tell me how to align the head. Any ideas?\015

Answers :

Check the positioning of the roller (it's got numbers 1 2 3 at each end, make sure it's on the same number at both ends).
\015\012
\015\012Just a thought too - check your power lead at the machine end as due to the age it may have deteriorated and the wire inside may be broken.
Repair Help & Product Troubleshooting for Kirby G5 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kirby G5 will not start. Head not aligned?


Check the positioning of the roller (it's got numbers 1 2 3 at each end, make sure it's on the same number at both ends).\015\012\015\012Just a thought too - check your power lead at the machine end as due to the age it may have deteriora ... Kirby G5 Bagged Upright Vacuum

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.


Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

I have a new Kenmore vacuum cleaner w/power head also Hepa Filter. The power head started once and will not start now. I have checked to make everything is hooked up right. The reset button is below


... Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

The ultimate g series kirby vacuum,,the spinner wont attach to the head?


... Vacuums

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on


... Miele Blue Moon Bagged Canister Vacuum

Power head stops and starts


The problem is with the connection between the flexible hose and the handle - there is a joint between the two that allows the flexible hose to rotate in the handle and the electrical connection here is not great!\015\012\015\012If the he ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Kirby turns on with hose attachement but not with head attachment


Front of the unit, black switch that is pressed by this plastic protrusion from hose coupling has two parts. It is because ANY generation Kirby has speeds - HIGH for vacuuming with hose and LOW for using it with nozzle.Looks like the switch we ... Kirby Ultimate G Bagged Upright Vacuum

The kirby wont start no power


... Kirby G6 Bagged Upright Vacuum

Thank you for the detailed explanation regarding the kirby vacuum functions, but we would like more information about the exact shampooing instructions. in explanation we would like to know exactly what solution and in what quantity to apply first to the fabric... how long we need to let it soak in.... and how to remove the stains using only our kirby vacuum witjh shampoo attatchment from start to finish...


... Kirby Ultimate G Bagged Upright Vacuum

On a Kirby sentria the metal spool sticking out that goes into hose or power head becomes extremely hot and left burns marks on brush tube. It only gets hot when using power head. I checked all adjust


Check the brush roll to be sure it's spinning free too much drag can cause that to get hotter but usually it would break the belt. That spindle will get hot from the friction created by turning the belt and from the motor's heat. They'll just get hot ... Kirby Vacuums

I have Kirby sentria that shuts off while using the rug attachment and won't start until I change to the hose attachment. I have had it in Kirby repair store 5 times, cord replaced. Took it back t


*power cord\012*power switch\012but most likely it is the black switches on the fan shroud. These are the safety switches that prevent the vacuum from turning on. ... Kirby Vacuums

Kirby Sentria I just got done usting the carpet shampoo system and now my Kirby wont start


When you replace the outer bag assembly, you have to make sure that it is turned clockwise untill it fully stops. There is a small switch on body of the Kirby that is only engaged when the bag assembly is installed correctly ... Kirby Ultimate G Bagged Upright Vacuum

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?


... Kirby Heritage II Vacuum

The motor in the power head ran at a higher pitch for a for 8 to 10 seconds then stopped. If I push the reset button the powerhead may or may not start or it may start and run for a few seconds. The brush is not caught.


Did you check the belt? A broken belt results in lower strain on the motor, causing it to run faster resulting in the faster speed and higher pitch. This could result in overheating, which will cause the motor to shut off.\015\012If this isn' ... Electrolux C101 Bagged Canister Vacuum

I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...


Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums

Our Kirby G5D won't start. - Kirby G5 Bagged Upright Vacuum


Make sure that both safety switches( in front and the bag are) are engaged. To see the video how to correctly attach the nozzle and bag go to:\015\012 http://www.goodvac.com ... Kirby G5 Bagged Upright Vacuum

Power Head keeps cutting in and out while vacuuming???Canister motor keeps running but the power head starts and stops like there is a short or some loss of connection somewhere. Any ideas?


My kenmore progressive vacuum had the same problem. The electrical terminal at the bottom of the wand was corroded. I used a flat head screw driver to scrape the female portion of the connector as best as I could. I then took off the plastic cover on ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

My kirby wont start - Kirby Vacuums


Check the plug,then check the switch. ... Kirby Vacuums

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition


Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

Kirby Sentria Hi, I have a new Sentria & used it for the first time today. It was going fine & then I could smell smoke & it started to make a loud noise so I turned it off quickly. If I turn it on it immediately starts making the noise again & I can see it is all lit up inside like something is burning or sparking. I have checked the roller & it is moving & I have checked the fan which is moving & doesn't appear to be damaged in anyway. This product is from the US & we are in the UK & we are us


Sounds like the motor burned up. not sure if travel adapters will handle a large load like a motor, around 8 or amps. power needs in US are 110 volts ac, 60 hertz.I believe UK is 220 volts and 50 hertz. usually when a vac is brought to eu ... Kirby Vacuums

I just bought a 2nd hand Kirby & not really know how to start. it didn't come with any operation Manual or CD. I realized its a re-po set. I think its Kirby Ultimate G Bagged Upright Vacuum, as there is nothing to identify it.


Here's a free guide for the shampoo system and I have both book and DVD manuals available for purchase. Hope i've helped...\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn't really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say 'push here to open'


Machine will not come on ... Kirby G6 Bagged Upright Vacuum

My DC 14 makes a terrible noise when I am vacuuming on carpet, so I put it in the upright postion and it stops. I but down the head and the noise will stop. If I bump the head it will start making the noise.


If the noise is rattly then it means the drive belt needs replacing, if your model has a protective brush on/off mode on the front plate where you would normally put your foot, it would have to be repaired officially by a repairer. Replacing a protec ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0326 seconds