Having problems with your Kirby G5 Bagged Upright Vacuum ?

The tech drive has come off, how do i put it back in place.


Answers :

The pedal assembly must be replaced,( part # 558401S), as it has a gear pressed to it which has come loose. The handle, switch plate, and upper motor cover must be removed first. To remove the plastic switch plate, remove it's screws and insert a flat screwdriver into the rectangular slot in it to pop it off. Four screws hold the upper motor shell in place. Next the switch button must be removed. The Techdrive assembly can be removed by removing the three screws on the bottom. Drop the drive down, and unhook it's belt from the gear on the end of the armature shaft. The pedal assembly can be removed by removing the remaining screw from the bottom of the drive unit. The N/D pedal has two parts - the pedal itself, and the shift cam. Observe carefully how these units fit together. After installing the new pedal and replacing the screw and washer to secure it, re-install the drive unit. The shift must be in the Drive position to install it, and remember to replace the belt. Be sure to line up the arm on the drive unit so that it engages the slot at the base of the handle pivot and re-install the other items.
Repair Help & Product Troubleshooting for Kirby G5 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The tech drive has come off, how do i put it back in place.


The pedal assembly must be replaced,( part # 558401S), as it has a gear pressed to it which has come loose. The handle, switch plate, and upper motor cover must be removed first. To remove the plastic switch plate, remove it's screws and ... Kirby G5 Bagged Upright Vacuum

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.


The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

I have a Kenmore Progressive Upright Vacuum - Purple, and it worked just fine. I emptied the canister (like always) and put it back in place. I turned on the vacuum to it immediately shutting down (motor) and only the lights come on. There is no movement/noise/suction at all! Any suggestions? I have tried everything. I have no idea why it did this.


Make sure that something didn't fall into the fan assembly in the base when the canister was removed. The motor should have an overload reset switch. Try moving the motor manually (power plug out) to make sure that it isn't bound up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Bearing by belt has come out. hOw do I get it back in place and put on a new belt? Thanks


Http://www.dyson.com/support/you can down load manuals at this site ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!


Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

The tension knob came off of the front of my sewing machine while I was sewing. I cannot figure out how to put it back on. I have the metal rod that fits into the back of the tension knob, but cannot figure out how to put it back into place. Keeps falling off


It sounds like your machine is the kind that has a knob with a 'set screw', a teeny tiny screw that tightens and holds the thing in place on the rod. Look for a small hole, probably on the bottom and look for a very small screw near the machine. ... Vacuums

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell cleanview 11 bagless special edition model 3576-2 I took apart to clean the filters and don't remember howto put the bottom of the dirt container back. I thought I put the empty container back in place correctly but the dirt when vacuuming is flowing through another part of the vacuum.


... Bissell Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

How do I put the safety lever back in place


... Sebo X4 Bagged Upright Vacuum

Hoover wind tunnel U6425 self propell drive pulley and nut fell off.Now when I try to put it back on and tighten it pulls the clutch assembly over so the accuator is in drive all the time and won'


... Hoover Vacuums

I had to replace the idler arm assembly because it snapped. I then had to put the torsion spring in place and that is where I am having trouble. I cannot seem to find a diagram that shows how it goes back into place.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I removed the handle of my Dyson DC24 to vaccum in high areas and now when i try to put the back piece back, it doesn't click. So when try to vaccum on the floor the handle just comes off.


Hi there,I'm sorry to hear you're having difficulty with your DC24. The wand handle should reattach easily to the machine, locking into place with an audible 'click'. If it doesn't seem to be doing this, you may want to check you have the han ... Dyson Ball DC24 Bagless Upright Vacuum

Pfaff quilt expression 4... the thread snipper blade has come out during cleaning, how do I put it back please. It does not mention it in the booklet that comes with the machine. Many thanks, Bobbie


Http://naehfabrik.forumprofi.de/wartung-pflege-von-naehmaschinen-f143/messerwechse ... Vacuums

I have a proheat carpet cleaner model 3 7901. the problem is the brush on the bottom of the machine plus the two end parts and the belt came out. i put everything back but they popped out, they are not staying in place. what am i doing wrong or what do i have to take out to get everything in place correctly?


Hi\015\012\015\0121. You’ll need to follow this procedure to assemble your unit back together.\015\0122. Make sure the foot pedal is in the proper position.\015\0123. The SmartMix should be properly loaded into the main ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My floormate is not suctioning very well. Tech support told me to take out the brushes and put them back in and this helped for a little bit then it went back to not suctioning. deb


When you took the brushes out, was there hair wrapped around them? Sometimes they just need to be cleaned off. When you take them off, there is a belt they connect to that also goes around a gear -- make sure the belt and gear don't have hair wrapp ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I have the electrolux guardian-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please :)


Hi,\015\012Check your hose you have something stuck in the hose...stretch it out straight and run something through it to push out whatever is stuck in there...\015\012\015\012heatman101 ... Electrolux Guardian Bagged Canister Vacuum

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu


Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

I have the Aerus Lux7000-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please :)


Hi, you very likely have a defective control valve under the dial on top of\015\012the vac , or a kink or blockage in the tiny pressure hose that feeds\015\012the air from the throat of the vac or the back of the bag chamber\015\012against the two si ... Electrolux Guardian Bagged Canister Vacuum

THE NEUTRAL/DRIVE LEVER HAS COME AWAY FROM THE HOOVER AND SOME OF THE INSIDES HAVE ALSO COME AWAY. I WOULD LIKE TO KNOW HOW TO PUT IT ALL BACK TOGETHER


I dismantled the cover, withdrew the gear drive assembly and found the bits that had come loose. The mechanism that selects neutral or drive had come away from its shaft. I simply put it all back together and tightened everything back up. Works a dre ... Kirby Heritage II Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0607 seconds