Having problems with your Kirby G5 Bagged Upright Vacuum ?

Our Kirby G5 chatters as I push foward over the carpet.


Answers :

Repair Help & Product Troubleshooting for Kirby G5 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Kirby G5 chatters as I push foward over the carpet.


... Kirby G5 Bagged Upright Vacuum

Bissell aroma pro upright carpet cleaner wont push foward keeps getting stuck


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

After running unit for about 15 minutes, when pushing the unit foward, spots of water appear on the carpet. Soap and water tank is full.


The water is going to be coming from a small seal in the bottom of the soap tank. I would suggest turning it on, on a hard floor. Then when you see that it is dripping, then trace the water back to the source. I am sure that it is coming from the soa ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Chatter We have a Kirby Ultimate G. Since we purchased it it bounces across the floor and the level of the sweeper has nothing to do with it. To get it to stop, it has to be at the highest level. The place we bought it, has done nothing to help us. We tried a new beater brush, no help. If I have to use it at it's highest level to sweep my carpet, I might as well not waste my time. ANy suggestions?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=576381\015\012Chatter\015\012Posted by CANRN on May 06, 2008\015\012We have a Kirby Ultimate G. Since we purcha ... Kirby Ultimate G Bagged Upright Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.


The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Bissell Proheat 2x Model 9200. The solution goes directly through to the carpet. The tank empties extremely fast even when I am not pushing the button. I have also noticed that I have soap spots on the carpet when pushing the cleaner forward. These spots are not even associated with the cleaning mechanism. I have inspected the cap on the tank, but it seems to be OK. Any suggestions?


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9200 Upright Vacuum

G-4 Kirby self propel unit works in reverse but not foward


Jon,\015\012Here is a helpful link to use to adjust the tranny. About a 7 on the difficulty level.\015\012\015\012http://www.greatva ... Kirby Ultimate G Bagged Upright Vacuum

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn't really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say 'push here to open'


Machine will not come on ... Kirby G6 Bagged Upright Vacuum

My Oreck XL 7000 is hard to push through a modest pile carpet. They gave us a shag attachment but all that does is push the carpet down. It is not ususable for us with bad backs etc.


... Oreck XL2200 Bagged Upright Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

I don't feel that the vac is close enough to the carpet anymore .. it's almost like I have to push the head down so it reached the carpet to roll the brush through it ... I've tried a friends vac and it shows nicely that you've just vacuumed the carpet .. heavy traffic areas are not getting pulled back up .. I have the short shag type carpet .. Thanks


Consider disassembling and cleaning your unit. Sometimes dirt and grit will build up, and when wiped away allow the moving parts to function better. Dysons are made to be broken down by the homeowner. A manual can be obtained here: http://www.manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.


I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Why wont my kirby carpet cleaner pick the foam and water off the carpet leaving my carpet soaking wet?


Is the carpet washer attached to unit is the belt hooked up? don't use the vacum head you well get shocked.be careful ... Kirby G6 Bagged Upright Vacuum

The suction is good, but it can't pick up most of the stuff on the floor. The hand held hose works very well, but it doesn't even pick up little fuzzies reliably when I push it along. And, the suction is too hard I think because it used to push easily and now I have to push really hard, even on flat carpet.


Check entire length of hose, including the piece in the power head, for clogs. Simply drop a marble in one end and allow it to roll out the other. If it doesn't, then the hose is clogged somewhere. ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

I have a very old kirby generation 3 unit that converst to a carpet shampooer. I was attemtping to shampoo the carpets but it does not seem to be picking any of the water back up out of the carpet. What am I missing?


Make sure the belt on the carpet shampoo aggitator is good, (could be stretched or broken) recommend replacing that belt. also make sure your fan in the front of the machine doesnt have any chips or cracks around the center. (this will cause lower su ... Vacuums

Kirby Sentria I bought my kirby sentria just before we were to move house and although I have the instructions somewhere, they will be boxed up and I so want to clean the carpets before I move. Problem is that I don't know whether the belt should be on or off when using the big silver front with the Kirby insignia on it. I know that the green light should come on when it is working properly and it does not, so I am doing something wrong. I can attach the attachments no problem but I want to use


If the green light is off, then its time to replace the band. This video shows you how. ... Kirby Ultimate G Bagged Upright Vacuum

Dyson 33 wont push on plush carpet


Hi there,I'm sorry to hear you're having difficulty using your DC33 on this particular carpet. If you haven't already contacted our Helpline, I'd encourage you to do so, as we'll be able to discuss other options which may be more suitable for ... Dyson DC33 Bagged Upright Vacuum

I cannot push my Dyson on my new carpet


... Vacuums

Dyson suddenly hard to push on carpet


I know this sounds silly, but it works. Turn it over and wipe all the black residue off the bottom of it (off the plastic on the bottom that rubs on the carpet as you push and pull it). I thought my husband was out of his mind when he told me that ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Smartstrand carpet makes vacuums difficult to push


The seam problem could be an installation problem. It is important to pattern match any carpet with a pattern. If the carpet is a plush carpet, the seams should not be invisible, but not unsightly. If he carpet is a frieze, the seams should be ha ... Oreck XLS700A Upright Vacuum

Why does my Oreck drag on carpeting? bought an Oreck upright 4.8 bagless at a garage sale. Great on the kitchen floor but seems to drag , difficult to push on the commercial carpeting. any hints


... Oreck Dual Power Electric Floor Sweeper Bagless Upright Vacuum

Kirby creating dirt under carpet?


It is possible that the height adjustment on your Kirby is to close to the carpet,which could account for the problem you're having.The correct height adjustment for your Kirby is this-Lower the height adjustment down until you hear a change in the s ... Kirby Ultimate G Bagged Upright Vacuum

Kirby Ultimate won't clean carpet


When you install the hose connector it trips a switch that switches the vac motor into high speed because the vac path is longer using the hose. check the belt after you remove the front. make sure the direction of rotation is in the direction of be ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0549 seconds