Having problems with your Kirby G5 Bagged Upright Vacuum ?

My on,off button came off how do i fix it

\015 I had took the bottom plate off to see why the drive was going to fast and when i did the on,off button came off i got the wire connect to the bottom of it i cant get the top back on and it wont turn off it turns off but not off\015

Answers :

Get local kirby enginere to rebuild your machine
Repair Help & Product Troubleshooting for Kirby G5 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My on,off button came off how do i fix it


Get local kirby enginere to rebuild your machine ... Kirby G5 Bagged Upright Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C


... Filter Queen Majestic Canister Vacuum

I set up my ONYX SW2300XS which I recieved as a gift (so no reciept) for the first time today. At first it was working well, I inserted a dvd and it played well. I played with the zoom and the skip buttons on the remote a bit and left it playing while I went a did other things. I came back about halfway thru my movie and wanted to skip scenes but the remote did not work. So I tried the NEXT button on the machine. This did nothing, so I tried the STOP button and that did nothing, the dvd was


Mine does the same thing! The store told me it would play all formatted but it does not! Its junk!! ... Vacuums

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T


... Rainbow E series Canister Wet/Dry Vacuum

Restart button Where is located that restart (or reset) button that fixed the problem? thanks a lot.


Usually there is a red reset button to push on top of the power head, but some are on the back edge of the powerhead. ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat


It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?


Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

Telescopic wand My wife's Electrolux Oxygen has a telescoping wand that expanded and contracted. All one had to do was slide a button and the lower tube slid inside the larger upper tube. Now the button no longer moves whatever was inside to allow the expansion/contraction to happen. How do I fix this situation? The wand assembly hardly seems to be made with repairs in mind. This method of manufacturing is annoying. Thanks, Eric


... Electrolux Vacuums

I have a new scoba (irobot) the battery is charged the tanks were fillied and every time i hit the power button and then clean the machines "check the tank" light came on. i have done all the proper instruction checks an i have done all the trouble shooting section. the machine will only work (and that is for 5 minutes drying its head) when i hit power and the clean button twice. so obviously the machine is somewhat working


We had to prime the sensor. irobot suggested a turkey baster, but we didn't have oneso we used an empty visine bottle with the end snipped off and rinsed completely. this worked after the first try. thank you for your interest ... iRobot 5800 Scooba Vacuum

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it


My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?


Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

My hamilton beach convection / rotissier over model 31197 oven button has a shortage in it, how can i fix it the button that turns the oven off and on, if you turn it on the oven doesn't come on but if you turn it counterclockwise all the way and hold it the light and the oven comes on. it was working this morning until i put a pan of biscuits in.


Sounds like a contact problem in the switch-Question: How old is the oven? Is it possible that the switch is worn out? If so-- and lets just say the switch cost $25, plus postage, would you want to invest that mo ... Vacuums

How do I fix wand release button and spring on dyson dc05


... Vacuums

Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.


I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums

Power won't stay on unless you hold the button down . How can I fix this and what is the problem?


You can't fix this problem yourself - a repair dealer needs to open up the button and inspect the power switch - call the Dyson helpline, they will find the closest authorized dealer in your area and if your machine is still under warranty it'll prob ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The neutral/drive mechanism came off. How to fix?


... Kirby G5 Bagged Upright Vacuum

How do i fix the on/off button on my dyson. - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


Greetings,Most likely your switch has gone bad, and you'll need to replace the on/off switch on your Dyson DC07. If you have to hold down the switch in order to keep the ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have an older model roomba 400 series. It was running fine until it hung itself on a power cord. Now it sits there with the clean button flashing orange. How can I fix this.


... iRobot Roomba 410 Robotic Vacuum

My vacuum was just working - I turned it off - now it won't turn on again. Nothing unsual happened. Now if I press the on button there is no noise or anything. How can I fix this?


Most likely the problem on these will be in the cord winder or in the actual switch. When I used to work for Electrolux this is what I remember seeing the most with the 7000. The best service you'll get on these are at an actual Aerus Electrolux deal ... Electrolux Lux 7000 Bagged Canister Vacuum

I have a sanyo performaX 900W UPRIGHT and in the last week i have not been able to get it to work anymore, ive tried different outlets and nothing at all happens, this occured just after i changed the bag Can you please guide me in how to fix this problem? does the vacuum have a hidden button inside somewhere?


... Sanyo Permax SC-A114 Bagged Upright Vacuum

Two things that looked like nails came out of my Dyson and not it is making a horrible noise like there is something bubbling inside. How do I fix it?


Sounds like you had some mounting screws come loose from the roller brush motor. There is no way to get at that part of this machine. It will need to go back to the factory and get it refurbished. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Electrolux Upright Versatility vacumm cleaner- When I use the CARPET power button, the roller does not work. Red wording lights up that says 'Check Rollerbrush'. How do I reset or fix the rollerbrush? thanks! I have guests coming and I really need to vacumm!


... Electrolux 1910 Bagless Upright Vacuum

I have a Miele S5980 vacuum cleaner, and recently had to change the Hepa filter. After doing the change, I tried resetting the reset button to switch off the Hepa filter indication light and it would not switch off. After a few tries, I accidentally depressed the switch, and it has dislodged from its cradle. Help, what can I do to fix this?


... Miele Vacuums

No Power Nothing happens when I push the power button. We've taken off the covers and found that there's a circuit board. Any suggestions on how to fix this problem. Thanks C


... Miele S 4210 Bagged Canister Vacuum

I have a Dyson DC17 and I cannot get the detachable hose to pull up to use. I have tried pulling it up but it does not move and I can not use my detachable pieces. Is there a button I need to press - How do I fix?


Yes there is a button to release it near the handle i think , \015\012\015\012hope this helps ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0632 seconds