Having problems with your Kirby G6 Bagged Upright Vacuum ?

Front wheel slips off shaft

\015 Right front wheel attachment slips off shaft\015\012Can't get it to stay on\015

Answers :

Pull the wheel off. Look on the back side of the wheel - you will see 4 plastic pins sticking out (inside the wheel) Use a pen to push on them - this way you will remove the hub cap without damaging it. Under the hub cap you will find the screw. You will need a torx T20 or Phillips crew driver (depending on what type of screw is there) to attach the wheel to the shaft with the screw. You can use a bit of a nail polish on the screw thread to keep from coming off again. DO NOT use glue or too much of nail polish or no one will be able to get the wheel of if needed some time in the future.

If hub cap nor the screw is there - you can find it all HERE.

Good Luck,
Rocky
:-)
Repair Help & Product Troubleshooting for Kirby G6 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Front wheel slips off shaft


Pull the wheel off. Look on the back side of the wheel - you will see 4 plastic pins sticking out (inside the wheel) Use a pen to push on them - this way you will remove the hub cap without damaging it. Under the hub cap you will find the screw. Yo ... Kirby G6 Bagged Upright Vacuum

How do I install the front wheels on a kirby sentria G10D? One of the front wheels broke completely off so I ordered the front wheel shaft assy but I didn't remove the broken one so I am having difficulty with how to put the new one on.


... RTO Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Right wheel slips off on Kirby Gsix . How do I fix it?


Hello,\015\012The shaft is held onto the machine with two little metal pieces on the bottom of the Kirby. They are held on with screws. The rear wheels are held onto the shaft with a little tiny "c" clip.\015\012\015\012Marci ... Kirby G6 Bagged Upright Vacuum

Front wheel problem


I would send it to protechrobotics. they will test all your components and let you know what needs to be done. if the repair is more than it's worth--they will help you out too.http://www.protechrobotics.com/ ... iRobot Roomba 4210 Bagless Robotic Vacuum

Hoover wheel assembly replace wheels - Hoover Fusion Vacuum Front Wheel Carriage 93001674


... Hoover Fusion Vacuum Front Wheel Carriage 93001674

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?


... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Replacing Front Wheel Assembly


... Vacuums

Belt Keeps slipping off shaft


If this is a new belt that keeps coming off, then if not catching something in the roller like a scatter rug, etc then the belt isn't tracking true. The pulley may have come loose for one thing, something has to be off to have the belt come off. Do ... Hoover U6434-900 Bagged Upright Vacuum

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

Need a front wheel assembly for my Hoover Tempo model u5144-900. I see similar looking Hoover wheel assemblies online for different models, will they fit mine?


The Tempo series cleaners look similar, but are different colors. The wheel assemblies will work if they look identical in appearance to yours. ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

Locked in down position.. won't go back up... looking at from the front.. the plastic clip at attached to the front vacuum wheel won't lock.. gears stuck


The extension pole will not go back down ... Dyson DC25 All Floors Bagless Upright Vacuum

On several occasions the belt has come off the Hoover Windtunnel beater shaft and had to be re-installed. Is there any way to prevent it from slipping off? The shaft seems to be made so that the middle if it is wider(thicker than either the end or the part closer to the motor, which, to me, is a bad design so I don't know how to overcome this problem. I'd be very grateful for a permanent solution to this problem. Thanks in Advance, mas


Your belt is stretched and needs replacement ( # 38528035 ) . The agitator is crowned so that the belt stays centered. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!


Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

Broken front wheel. Accidentally dropped it and broke the plastic that holds the wheel in place. Want to replace it with an unbroken one from and old dirt dog that no longer works.


... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

The right front wheel came off my G6 Kirby vacuum, then the entire axle and wheel adjustment came loose--including a spring that was attached to something.


Thank heavens for a husband who can fix anything--and save me a lot of money for repairs and advice! ... Kirby Vacuums

Fan belt wheel missing. Took it apart and discovered fan belt torn and no wheel on drive shaft for brush. I am assuming that there was one there originally.Did it shatter or what.What is solution. Can I get exploded view of this model or others like it.


Get another fan belt wheel of the model and place it over it ... Vacuums

Front wheel fell off Ultimage G Kirby vacuum


... Kirby G6 Bagged Upright Vacuum

How do you remove the front wheels of a henry vacuum cleaner?


... Numatic Henry Bagged Canister Vacuum

I need part number of front wheel assembly...


Part number for the wheels [you'll need to order two] 74818a-119n, the axle is part no. 71478 - available at sears 1-800-4myhome ... Eureka 4700A Maxima Bagless Upright Vacuum

Installation of front wheel assembley on a hoover vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My Bissell Dirtlifter Powerbrush carpet cleaner will not roll. The back wheels roll fine, but when you put the machine down flat, the front part (where the roller is) sticks and will not roll.


I had the same problem. It would pull backwards but not go forward. A closer examination revealed the clear plastic part on the bottom in the very front of the machine had popped loose on one side. If you look at the front of the machine, th ... Vacuums

Hoover front wheels replacement


On the wheel assembly you will see on each end the studs with the flat ends on them,slide the studs in the slots and fold wheels forward and push in.in the middle at the front of the wheels you will see a flat catch ,push it up into the base right be ... Hoover Elite U5061-900 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0178 seconds