Having problems with your Kirby G6 Bagged Upright Vacuum ?

N/D switch came out of housing

\015 My n/d switch came out will I was vacuuming. I am very handy and I dropped the transmission and I am now wondering if the splines are no longer goo and that hammer piece how does it go on the n/d switch??\015

Answers :

If the pedal shaft came out - it may be very hard to install it back properly and most likelly it will fall out again soon. You may need to get another N/D pedal assembly. To buy it you can go HERE. If you want to try to get it back together - go HERE and scroll down. You will see the section that explains how the pedal works so it will give you an idea how you have to assemble it.

Good Luck,
Repair Help & Product Troubleshooting for Kirby G6 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

N/D switch came out of housing

If the pedal shaft came out - it may be very hard to install it back properly and most likelly it will fall out again soon. You may need to get another N/D pedal assembly. To buy it you can go ... Kirby G6 Bagged Upright Vacuum

Plugged my Dyson in this morning, switched it on and power came on for not even a second and died. No power what so ever to dyson - checked my house sockets, changed fuse. Still not working - dead as a door mouse. What could it be? Many thanks Sam

It is either your power cable, cable rewind mechanism or your motor. \012\012Try switching it on, and wiggling the lead near the plug and see if it fires up. If it does, remove the moulded plug and fit a standard plug. \012\012If not, lik ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after

... Vacuums

Hoover power drive u6311 - How do u change switch? Does anyone have any idea how to remove the on and off switch, when I tap on the housing the motot and light goes on and off. Also does somebody have a exploded view of this model. also does anyone know the part number of the switch.

The swrtch is located in the bottom section of the motor. When the swtcih goes out it time to repalce the unit. The swtich is part of the motor. The switch rod run all the way down the body to the swtich located in the motor. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

I have a Kirby G4 it will start with the hose attachment but not the vaccum housing attachment ? I'm guessing a problem w/ the switch ....when I look at the switch I see two buttons I can actually

Check this vieo out these are safty switches ... Kirby G4 Bagged Upright Vacuum

Bissel steamer I took the base of the steamer apart and had trouble putting back together. The switch assembly the adjusts the flow of soap came apart. I dont know how to line up the the black valve to the switch. [email protected]

You can do this Jeremy just be take your time be patient and keep trying! ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o

Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

We recently bought a home with a 52" Hampton Bay Berlini Model 729 395 ceiling fan with a light that operates on a remote control. There is also a wall switch plate with two circular controls - one pushes and spins, the other turns with 4 clicks. We can not get the light or the fan to operate using either the switches or the remote. We have checked the circuit breaker. The manual that came with the unit - provided to us from the previous homeowner - really only describes how to install the uni

Nancy do you want to sell the Berlini fan if youstillo have it? ... Vacuums

I have a 3 year old NuTone CV 353W central vac system and recently the switch on the hose handle does not turn the system on from any outlet in the house. I have to plug the hose into the outlet and then turn the unit on from the switch on the cannister. Any help would be greatly appreciated. Thanks

A great way to check if your switch in the hose is bad would be to turn the hose sideways in the inlet. If the unit turns on you most likely need a new switch. ... Broan-NuTone CV450 Central Bagged Central System Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!

Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I purchased a utilitech 7-day digital in-wall timer #0141224. My house wires are two black wires and a green ground wire. The new timer has a w,g, r, and b, wires. My question is what wires do I connect. I found the black power wire from the house. I have no white wire in the switch box. Where would the red wire go? Thank you

Hi!!\015\012\015\012\015\012\015\012The Green wire goes to ground, \015\012The White wire is the neutral. (in this case is used to supply power to the clock.) ... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

How do I remove switch housing on dyson dc18?

I have a similar problem and want to check the switches...the last release is not apparent...appreciate some help...[email protected] ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Henry Hoover throwing trip switch in house

Sounds more likely to be the switch than the motor, especially if it is the model with the top switch rather than the side "rocker" switch. If you are in the UK, speak to the technical people at ... Numatic Henry Bagged Canister Vacuum

DYSON DC04 how to remove switch housing to check

Its most likely not the switch, check the power cord.. check where the cord meets to the vacuum. the cord could be going bad and most likely not a loose wire. ... Vacuums

Sparks came out of the area of the foot switch and

This is now a dangerous appliance and should be repaired by a qualified tec ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

How do you remove the switches housing cover on a Dyson DC25?

... Dyson DC25 Animal Bagless Upright Vacuum

Hoover windtunnel vacuum overheat switched is set off too frequently and I cannot finish vacuuming the house in one session. Lemon?

Please remember this part is doing a service to you. its basically saying my motor is getting so hot picking up this dirt that i better make him rest before he burns up. in most cases you will find that you either have a clog or your filters need to ... Hoover Vacuums

My shop vac blows and doesn't ****! I put the hose on either hole and it blows dirt all in my house. I'm trying to vacuum. I can't find a switch to change it from blowing to sucking and if I put the hose in either hole it just blows.

... Eureka 2812 Wet/Dry Vacuum

My BROAN CV-110 hose with the rug beater only works if I turn it on from the base unit. Shouldn't it turn on when I plug the hose into the wall recepticle? Do I need to replace the hardware at the end of this hose and if so, where would I purchase that? This central vac came in a house I just purchased. Thanks for any help. Sherry

... Broan-NuTone CV450 Central Bagged Central System Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]

... Miele Vacuums

Will not turn on. tried different outlets and replaced bag. came on for a second then stopped working even though switch was on. trying to only use hose.

It is probably clogged up or its suction motor is burned up. Hop this helps!?\012\012\012Please rate solution - Thanks. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I have only had my shark steam mop for about a month and only used it twice. I tried to use it yesterday and it would not work. The green light came on and it worked for maybe ten seconds, then it completely shut off. I tried switching outlets and draining the water but nothing worked. It still doesn't work today either. What do you think is wrong? Does this product have a warranty?

Yes has warranty call Shark/europro. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

No power going to hoover have hoover turbo power 3. Plug is sealed but have changed fuse. Have had builders in house using it to renovate bathroom. Do you think it is now passed its sell by date was working until they got it. It dosent even switch on. Am ready to do them an injury as my upstairs is a mess

A Neighbour fixed it ... Hoover Vacuums

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0345 seconds