Having problems with your Kirby G6 Bagged Upright Vacuum ?

Kirby g6 My kirby is running louder than usual. Kind of like its screaming instead of running now. Its working fine, but the noise is really unbearable. What could it be?


Answers :

Could be the bearings, especially if the machine is old or the dust filters have not been replaced regularly.
\015\012Check to see if the noise is still present after the machine winds down when the power is turned off. A rattling sounds means bearings.
Repair Help & Product Troubleshooting for Kirby G6 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby g6 My kirby is running louder than usual. Kind of like its screaming instead of running now. Its working fine, but the noise is really unbearable. What could it be?


Could be the bearings, especially if the machine is old or the dust filters have not been replaced regularly.\015\012Check to see if the noise is still present after the machine winds down when the power is turned off. A rattling sounds means b ... Kirby G6 Bagged Upright Vacuum

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

I have a cb9191j-10a vacuum that works fine but I am really disappointed by the small screw-on filter that quickly clogs up with dust and debris. There must be a larger type filter that could be used and this would make for a really fine vacuum. Could you suggest an alternative filter?


... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Kirby Sentria Hi, I have a new Sentria & used it for the first time today. It was going fine & then I could smell smoke & it started to make a loud noise so I turned it off quickly. If I turn it on it immediately starts making the noise again & I can see it is all lit up inside like something is burning or sparking. I have checked the roller & it is moving & I have checked the fan which is moving & doesn't appear to be damaged in anyway. This product is from the US & we are in the UK & we are us


Sounds like the motor burned up. not sure if travel adapters will handle a large load like a motor, around 8 or amps. power needs in US are 110 volts ac, 60 hertz.I believe UK is 220 volts and 50 hertz. usually when a vac is brought to eu ... Kirby Vacuums

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

I shampooed my carpet and later that day went to use the Kirby Sentria and it wont turn on... it has always worked fine up to this moment, what could be wrong?


Specifically the bag attachment area. There is a detent on the bag boot that depresses a safety switch. Make sure the bag boot is rotated clockwise into its seated position. ... Kirby Heritage II Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad?


My first recomendation would be to try pluging into a diffrent wall outlet as well as something that is on a diffrent circut . It is a known problem that the pins inside that make the connection could be worn out . There are several pins from the one ... Kenmore 21513 Vacuum

Miele S318i worked ok till I took it apart to blow really fine ceiling "popcorn" dust that got sucked by the filters. When I plugged back in started for a milli second and quit. At this point I believe the circuit board might be the fault, but I want to test motor before I go and buy the part. Can I simply run 110 to the two moter contacts to bench test? Steve


Yes, you can. ... Miele S318 Bagged Canister Vacuum

My machine ran over some string,made a funny noise and emitted some smoke,the hand suction pipe at the rear works perfectly, the motor runs fine,but the front of the vacuum will not work.thankyou very much, Thomas.


The string bound up the beater bar (brush), keeps the belt stationary, and the motor spindle is just rubbing against the belt and melting it. remove the belt guard, remove the brush, and the belt. clean off the brush bearings (at the ends of the br ... Panasonic Vacuums

Motor quit working. i was vacuuming and all seemed fine. then the motor went really low. when I opened it I noticed that the bag was not attached and the cannister had filled up with stuff and the filter was full. the vacuum will not run now.


My friend, the dirt you sucked up went right into the motor and it burned up. I am very sorry to tell you this. It is probably not worth repairing unless you are able to replace it yourself.\015\012\015\012In addition to not being able ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I have a Miele s251i vacuum that was working just fine until I umplugged it (while running) and re-plugged it in at a closer socket. When I replugged it, it started for a second and then stopped. Will not start now whether we use the on/off switch or not...suggestions? Would also like to know how to disassemble the unit so I could check out the wiring with a multitester..thanks


I just had exactly the same problem. Opened the vac, checked the circuit\012 next to the motor and it can be clearly seen that the Triac burned thru\012 the PCB. Will replace it and check again. Vac bought long ago, works \012extremely well. ... Miele Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

My scooba seems to work fine but no longer makes the beeping noise. Several weeks ago the beep was sounding very strange almost like a battery was dying. Now it's not making any noise at all. Is this the beginning of more problems or can the machine function just fine without the beeps? If not then how can I fix it?


Your speaker went out. It could be totally isolated. You're not going to be able to determine what's wrong with your Scooba if something does happen, though, because without those beep codes, there's no way for the robot to communicate with you. ... iRobot 5900 Scooba Robotic Wet/Dry Vacuum

My DC500 works fine running on battery power, but the motor hesitates for a moment or two when the unit is switched on with ac power. After this it works fine. What might be wrong?


May be the carbon brushes are short or motor connectors have become bad connection by moisture and dirt by use temporay a wrong filter sometimes its a very light and simple motor johnson motor with hammer brushes \012 ... Dewalt Vacuums

Loud noise?? my vacuum suddenly just got really loud. it suctions fine, i changed the belt, but when the roller is off its not loud, but when i put it back on the 11noise is horrific. it vacuums fine i just cannot stand the noise. please help


I have the exact same problem. I've taken the thing apart and cannot figure out what is causing the noise. It's not the belt and it doesn't seem to be coming from the engine. It sounds like the spinning brush is hitting something, but it's not, th ... Bissell 6590 CleanView Bagless Upright Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0756 seconds