Having problems with your Kirby G6 Bagged Upright Vacuum ?



Answers :

I had to replace the hose end on my Kirby, the motor end. I have the Diamond edition. Just take a hair dryer and get the end of the hose warm, and then us a screw driver. Works like a charm. It stays warm long enough to put the new end on.
Inside the machine end of the hose is a round rubber ring that holds the hose into the hose end. Take a flathead screwdriver and push the edge of the rubber ring towards the center and downward. MAKE SURE THAT YOU DON'T STAB YOURSELF IN THE PALM WITH THE SCREWDRIVER! lol
It should come out with some hard pushing. Now, just push the edge of the ring inwards again and hold it in place with your other hand. Put it up inside the new hose end and then use the screwdriver to smash the edge back out again to hold it in the new hose end. Hope this helps! Here is a link to find the repair part that you need to fix your hose...
Repair Help & Product Troubleshooting for Kirby G6 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each

Should be a pry off dot on the underside revealing a screw ... Vacuums

I have some sort of object in the hose of my Epic 6500. I have tried reversing the hose and blowing out the foreighn piece of debeis but this has not worked. Is there a way to remove the plastic connector end to access this end of the hose? Or is there another solution to this problem?

By reversing it, I assume you plugged the hose into the exhaust blower on the top of the machine. If so, insert the other end into the intake and turn one the vacuum. This way the clog is also getting sucked at what should be the loose end.\0 ... Electrolux Epic 6500 Vacuum

Clogged hose... I have a clog in my hose, probably a sock, I have pushed it through to the hard plastic handle end of the hose, help! can the plastic handle wand be disconnected from the hose to remove the clog??? Thank you

Hi!\015\012 \015\012Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Con ... Bissell 6594 PowerForce Bagless Upright Vacuum


I had to replace the hose end on my Kirby, the motor end. I have the Diamond edition. Just take a hair dryer and get the end of the hose warm, and then us a screw driver. Works like a charm. It stays warm long enough to put the new end on. ... Kirby G6 Bagged Upright Vacuum

How do you remove the plastic end fitted to the flexible hose

Not necessarily. Some Dyson models have an all inclusive flexi hose which attaches to the handle spine. Check EBay for replacement flexi hoses - UK has many sellers - or handles which have the metal pole and the flexi tube attached. \015\012\015 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I cleaned out the hose and removed brush to clean and checked belt. Everything seems to work but will not pick up or suction on carpet. The hose is totally clear from clogs. I can see the floor from one end to the other. What am I missing that might be causing lack of suction?

Hi troupdavid,I see that your Vacuum is having issues with it suction, you mentioned that you took it a part to clean it, see steps below.\015\012\015\012Check if everything is inserted prope ... Hoover Tempo Widepath Upright Vacuum - Blue

I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks

Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums

How do you remove the attachment end off the hose?

Most hoses detach from the wand by twisting,or push button release. Please advise what BRAND ... Vacuums

Miele S7210 upright how do I remove a split hose from the handle end

THIS LINK IS THE MANUALhttp://www.totalvac.com/manuals/miele-vacuum-S7000-manual.pdf ... Miele S7210 Bagged Upright Vacuum

Repair need to replace the hose how do I remove the ends

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!

Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

I have a dyson DC07. The hose has come away from the hose end and the end is stuck in the top end of the wand as it sits in the upright position on the machine. Any ideas as how to get it out? If I can get it out it might just be a new hose. If not, it's a new hose and wand.t

... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!

Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is

... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak

... Kenmore Progressive 35922 Bagged Upright Vacuum

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss

Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg

Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

Kenmore canister vacuum 25812500 hose end replacement

... Kenmore 22822 Canister Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron

The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.

You don't have to take the vacuum apart.\015\012Assuming this is an Epic 3500 or similar upright Electrolux:\015\0121. Lay vacuum on it's side.\015\0122. Gently pull hose from power head. It's not screwed in so that should be eas ... Electrolux Epic 3500 Vacuum

How can i put on the snap ring on an eloctolux vacuum hose on the end piece of the hose; it is a swivel end and an older vacuum cleaner plastic canister type

The snap ring is generally found on a Canadian made LUX AP series prior to 1982 and it is in fact a coil spring you must leave the wiring off the handle. Be sure the steel cap and rubber o ring are on the tip of the hose. Slide the handle onto the ho ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I want to remove the hose from the handle of the vacuum? I already removed the plastic clip. I thought that would free the hose, but it did not. Any ideas?

There are two discs on top on the dandel that cover the screws. You need to remove the two screws and the you can take the handle off the hose.\015\012\015\012Bob\015\012 ... Electrolux Centralux Vacuum

How to replace just the Kirby 210097 Hose End For G5 Series Vacuum Cleaner to hose. can buy replacement but can not get the broken end off

Simple and rquires no tools. Fill your sink with hot water and set the end in water with attachment on it. Within a few minutes the end is soft enough to slip out. setting the hose end in the water again will let you simply slip the hose into the ... Kirby G5 Bagged Upright Vacuum

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.

Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0544 seconds