Having problems with your Kirby G6 Bagged Upright Vacuum ?

My brush won't spin, and won't **** well - Kirby G6 Bagged Upright Vacuum


Answers :

U need a new band inside they break and it stops the brushes spinning
Repair Help & Product Troubleshooting for Kirby G6 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My brush won't spin, and won't **** well - Kirby G6 Bagged Upright Vacuum


U need a new band inside they break and it stops the brushes spinning ... Kirby G6 Bagged Upright Vacuum

The brush does not spin when shapmooing - Kirby Ultimate G Bagged Upright Vacuum


Turn it upside down, see if you can the belt that driven up the motor gear, maybe it is mis allign or loosen. if it need a replacement then have it replace ... Kirby Ultimate G Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Kirby g6 carbon brush change - Kirby G4 Bagged Upright Vacuum


This guide has the answer... http://ww.ebay.com/gds/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VA ... Kirby G4 Bagged Upright Vacuum

Oreck upright brushes not spinning - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

Roller doesnt spin on my kirby g series - Kirby Ultimate G Bagged Upright Vacuum


That means that the belt is stretched or broken. You need to replace it. You can get replacement belts here:Kirby Ultimate G Belts ... Kirby Ultimate G Bagged Upright Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums


Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Brush is not spinning - Miele Powerhouse Plus Bagged Upright Vacuum


Usually, this is caused by the brush assembly end bearings becoming bound up with string, thread, and hair. Remove the brush and clean the bearings and end shafts. Oil them lightly with 3-1 oil or similar. Check the condition of the drive belt and re ... Miele Powerhouse Plus Bagged Upright Vacuum

The brush stops spinning - Dirt Devil M086355 Bagged Upright Vacuum


... Dirt Devil M086355 Bagged Upright Vacuum

The brushes are not spinning - Oreck XL® Classic Bagged Upright Vacuum


It sounds to me that the drive belt to the brush is broken. To verify, or replace, you must take off the bottom cover. ... Oreck XL® Classic Bagged Upright Vacuum

How to remove brush roller ultimate g - Kirby Ultimate G Bagged Upright Vacuum


Http://www.youtube.com/watch?v=At7tqnjD-Kc ... Kirby Ultimate G Bagged Upright Vacuum

U6485900 brush wont spin - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Check the belt av not broke this link is for the manualhttp://hoover.com/file/509/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dyson dc 33 brush bar not spinning - Dyson DC33 Bagged Upright Vacuum


... Dyson DC33 Bagged Upright Vacuum

The brush won't turn. - Kirby G4 Bagged Upright Vacuum


Are you certain the belt attached as it ws suppose to when you locked the front onto the base? ... Kirby G4 Bagged Upright Vacuum

The vaccuum brush is not rotating - Kirby G5 Bagged Upright Vacuum


... Kirby G5 Bagged Upright Vacuum

Brush heads won't spin - Bissell 3522 PowerForce Bagged Upright Vacuum


Your belt is stretched, worn or broken and therefore not turning the brush. Here is a link for the replacement belts you need and the manual which has instructions: ... Bissell 3522 PowerForce Bagged Upright Vacuum

Brushs arc against spinning motor - Oreck XL2000 Bagged Upright Vacuum


... Oreck XL2000 Bagged Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have a Kirby G4. I have noticed the last few days when trying to vacuum that it is blowing more than it is sucking up. I put on a new bag to make sure it wasn't too full. I also put on the hose and noticed it's not sucking as well as normal. I unzipped the back of the bag holder and noticed the bag isn't inflating as it should be as well. I appreciate any advice. Thank you.


Take the mini emptor off(plastic piece on bottom of cloth bag) this is done by rotating it away from the body of the machine. There is most likely a clog there. Also take the brush head off and inspect fan for chips or cracks this will also reduce su ... Kirby G4 Bagged Upright Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kirby skips while vacuuming carpet - Kirby Ultimate G Bagged Upright Vacuum


... Kirby Ultimate G Bagged Upright Vacuum

How to change a band on a kirby vacuum? - Kirby Ultimate G Bagged Upright Vacuum


I think you mean belt??\015\012Take the nozzle of, remove the brush roll, put the a new belt over the brush roll, re-install and put the bottom plate on, making sure that the belt is in the middle of the brush roll. Turn the big knob on t ... Kirby Ultimate G Bagged Upright Vacuum

Where can I find kirby heritage vacuum brush belt 301282 and the vacuum bags for a 1984 kirby heritage?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1160 seconds