Having problems with your Kirby G6 Bagged Upright Vacuum ?

The drive/neutral lever on my Kirby 2000 G fell off. How do I fix it? I disassembled it removing the the top covering the motor and the bottom where the lever goes in, now I'm kinda stuck...


Answers :

Repair Help & Product Troubleshooting for Kirby G6 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The drive/neutral lever on my Kirby 2000 G fell off. How do I fix it? I disassembled it removing the the top covering the motor and the bottom where the lever goes in, now I'm kinda stuck...


... Kirby G6 Bagged Upright Vacuum

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!


... Miele S7210 Bagged Upright Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off


I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums

I am triing to remove the top part of a g1 sebo upright from the bottom half so i can remove the cover


... Sebo Essential G1 Upright Vacuum Cleaner

My Filter Queen just started making noise from the motor area, it was very hot. Upon removing the top thing that covers the area where the air blows out, there were sparks and it smelled pretty bad. My guess is the motor is shot. Is this difficult to change?


The motor will need either a rebuild with new bearing, or replacement. Parts should be no more than $100 .EASY project. 20 minutes max fro a pro shop. If you can tie your shoes you can do this one yourself. If replacing, upgrade to a ball/ ball ... Filter Queen Majestic Canister Vacuum

Malfunction 8 franke flair. I have removed the brewing unit o rings to free up the drive. Drive motor keeps over running the top and bottom limits hence gears grinding. Could it be the sensor on the back of the motor? What is it measuring? Any help appreciated


... Vacuums

My Bissell 3920 motor is making a high pitched noise. I have cleared out pet hair from top to bottom. Cleaned the lower filter and replaced the upper filter. I Checked for blockage in the hoses and found none. The filter indicator goes green when I turn it on, but the straining motor noise persists.


Click on the link below to view the replacement motor and fan for your Bissell 3920 vacuum\015\012\015\012http://www.vacuums24x7.com/motorfan.html ... Bissell 3920 Bagless Upright Vacuum

I need to replace the agitator belt on a Hoover Elite U4465-9 upright vacuum cleaner. I have removed the bottom cover, but there is no access to the motor spindle to loop the belt around. How do I do this?


... Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Eureka model 4335 - belt removal (top cover)


Hi.  There are 16 different models of Eureka 4335, and frankly I don't know how much difference there is between them.  You can download a copy of the user manual from the website below.\015\012\015\012If that doesn't work for you, pl ... Bissell Flip-It Select Hard Floor Cleaner - Volcanic Satin

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.


Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

Can't remove bottom cover


You need to get off two more screws on the lower compartment, whtere the powermate jr. is. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?


... Vacuums

Remove bottom of cover on vacuum bottom. Making a


On this model, the bottom does not come off but the top does. on the top hood there are 2 latches to turn with a screwdriver and the hood will come off. ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

How do you dismantle a Panasonic MC-3920 vacuum cleaner? I have removed the 4 screws at the top but still doesn't come apart and one got ideas. How do you remove the blue top cover ?


... Panasonic MC-3900 Bagged Canister Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug


Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

U6446-900 the drive cable came off and I need to remove the top cover so I can reattach the cable but I can figure out how to remove the cover


From the underside:\015\0121. remove 4 screws holding agitator cover in place\015\0122. remove 2 screws (black screws) holding hose retainer in place, pull hose out through top\015\0123. remove three screws, 2 long, 1 short holding top cover: short ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0610 seconds