Having problems with your Kirby G6 Bagged Upright Vacuum ?

I need to put a belt on..i have the head off, and have the knob on the front in the belt off postion, but where does the belt even go?


Answers :

Greetings,
\015\012
\015\012We have made a video demonstration for this particular repair. Changing the belt on the Kirby is never fun, but this easy to understand video should help you out and make it easier for you.
\015\012
\015\012Here's our video repair of how to replace the belt on your Kirby G6:
\015\012
\015\012
\015\012

\015\012
\015\012
\015\012
\015\012I really hope that this video was able to help you put the belt and the head of the vacuum back on. It's a handy video to have when it's time to change the belt. If this was helpful, kindly rate the video as helpful by clicking the Thumbs Up icon in the lower right hand corner below.
\015\012
\015\012Feel free to write a repair clarification if you have any further quesitons.
\015\012
\015\012Thanks again,
\015\012
\015\012Chris J.
Repair Help & Product Troubleshooting for Kirby G6 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to put a belt on..i have the head off, and have the knob on the front in the belt off postion, but where does the belt even go?


Greetings,\015\012\015\012We have made a video demonstration for this particular repair. Changing the belt on the Kirby is never fun, but this easy to understand video should help you out and make it easier for you. \015\012 ... Kirby G6 Bagged Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Hi my hoover vacuum, stopped working,does not even turn on,I accidently went over a shoelace but stopped before the shoelace went in, ,,becuase of that the belt came off,and then i put belt back on, and now it wont even turn on


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I can't turn the belt off of my Kirby vacuum. I had the front off of it earlier to attach the hose, but now when I put the front back on, I can't get the belt to turn off. The lever twists about 3/4 of the way around, but will not go the rest of the way.


Turn the front part to the green so it is level and then twist the front to the red make sure the belt catch the hook as you twist it then if the belt is hooked just put it back on the vac like normal and lock it in place then twist it back to the gr ... Kirby Ultimate G Bagged Upright Vacuum

The tension knob came off of the front of my sewing machine while I was sewing. I cannot figure out how to put it back on. I have the metal rod that fits into the back of the tension knob, but cannot figure out how to put it back into place. Keeps falling off


It sounds like your machine is the kind that has a knob with a 'set screw', a teeny tiny screw that tightens and holds the thing in place on the rod. Look for a small hole, probably on the bottom and look for a very small screw near the machine. ... Vacuums

My oreck upright smells like rubber burning when i vacuum. i just put a new belt on but it smelled like that before i even put the belt on


... Oreck XL Ultra Bagged Upright Vacuum

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.


I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?


... Eureka Capture Upright Vacuum Vacuum

Son took the front plate off the kirby heritage II vacuum thinking that was how to replace the belt, now don't know how to put the three rings and belt catcher back on?


Looked at a kirby vacuum that a family member has and saw how it was assembled! Thank You ... Kirby Heritage II Vacuum

D.d vaccum i have a dirt devil dynamite...i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!


Did you check the brush roll, if the ends aren't turning freely, then it needs to be replaced also. ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Bagless Windtunnel (tank tyle) selfpropeled head throws belt; 2nd one doing exactly as the first vacumm.very hard to put it back on .can't even get one room done


Is this a new belt? If not, get a new one. Check the brush roll, make sure the ends are turning freely, if not, replace it. If you are catching things like a throw rug and towell or some other thing, this will cause the belt to get knocked off of ... Hoover Vacuums

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position


I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums

My Bissell 9200 is not even a year old and the motor which drives the dual rotating brushes at the front of machine does not rotate. Please note belts are intact and are in good condition. Motor is not functioning.


... Bissell Vacuums

How to refit the front brush belt driven roller ? We removed the roller accidentaly when cleaning out hair that had got wrapped around the roller. How can we put it back in?


Hi well if you go onto youtube and look for replace dyson clutch it will show you how to refit your brush good luck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Put new belt on and the wheels are to high in the front of sweeper


THE WHEEL ASSEMBLY HAS TO BE PUSHED DOWN TILL YOU HEAR IT SNAP INTO PLACE ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

My Kirby G6 light is not turning on when I start the machine. I took off the front piece and removed a lot of hair from the roller and interior. Since I did that, the belt keeps coming off (even though it is fairly new). Is that the reason the light won't turn on? Is there any advice you can give me before I take it in?


The light indicates that the brushroll is spinning. If it isn't coming on, the power nozzle may have been reinstalled incorrectly. Take the nozzle off and then use my step-by-step guide to reinstall it. I expect that it will take care of the problem. ... Kirby Vacuums

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of


Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?


The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

My Mom has a Dirt Devil Featherlite and the belt falls off all the time. I put it on three times today and it falls off within a few minutes. The belt post I put it on doesn't have anything to hold the belt on. Is there supposed to be something holding the belt?


It sounds like the belt is too worn and loose to stay on. Buy a new belt specified for that model of vacuum and install. Ensure that there is only a slight amount of give in the belt when you press the middle. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Got Dirt Devil Featherlite,keeps burning the belt out immediately and there is only one way to put the belt on...have put on 4 new belts.....what up?


Hi There,When a belt breaks immediately after installing it, this can ONLY mean one of two things. The first is that the belt was put back on incorrectly, and it may be pinched underneath of the beater bar. This would cause it to bre ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0546 seconds