Having problems with your Kirby G6 Bagged Upright Vacuum ?

Drive mechansism won't engage Kirby g6

\015 Vacuum works on attachment mode. Belt is intact, but drive mechanism won't engage (head doesn't spin).\015

Answers :

Repair Help & Product Troubleshooting for Kirby G6 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Drive mechansism won't engage Kirby g6

... Kirby G6 Bagged Upright Vacuum

I have a kirby vacuum model G7D when engaging the tech drive, the machine zips forward to fast, the main suction mech rears up and won't stay on the floor. A technician replaced the nutural drive assy. Could he have caused some mechanical malfunction to occur??

My understanding of Kirby vaccums is that they are lifetime warranty. It appears that the drive assembly that was installed was not adjusted properly after it was put in or it is defective. I would see about getting it back to the tech for further wo ... Vacuums

Kirby gen 3 wont go out of drive

Cam neutral button worn, contact your local kirby agent for service or kirby.com ... Kirby Generation 3 Bagged Upright Vacuum

Kirby g7d wont go into tech drive

... Kirby G5 Bagged Upright Vacuum

My Kirby G6 Techdrive pedal came out of the machine. I do not see how to secure it in the unit so it will engage and disengage the drive. Any guidance? Did something break or come off of the shaft?

\015\012The Kirby Gsix is equipped with TechDrive Power Assistant. This feature makes it very easy to move your vacuum back and forth, eliminating any effort on your part. The KirbyTechDrive pedal is opera ... Kirby G6 Bagged Upright Vacuum

Kirby g 5 head bounces when vacuuming and tech drive is engaged, does not do this everytime

First change the belt, even if it is not broken. also make sure that the height adjustment is raised up high enough, the higher the better ( when adjusting a vacuum you want the tips of the brush roller touching the tips of the carpet fibers ) also t ... Vacuums

I have a Kirby G5 vacuum that when light pressure is put on the handle it moves forward but in a jerky movement. Like the drive is engaging and disengaging. If you keep forward pressure on the handle the jerkiness does not happen. Is there an adjustment to correct this.

I hope adjusting position of the position of the "pivot spring assembly" will help. but you may have to disassemble entire slide assembly to clean it up if it still does not work smoothly. See instructions ... Kirby G5 Bagged Upright Vacuum

G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.

Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

G5 Kirby drive problem

There might be a problem with slide assembly. Some free movement is OK but sometimes the slide sticks and Kirby "keeps going".See THIS article ... Kirby G5 Bagged Upright Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

I have kirby k5 it will not go into the drive .I took it apart and the shaft that put it into drive 'had fell out.Not sure how to get it in the rightway to make it go from nut. to drive Are therea parts page you can email so i can see how it works thanks john [email protected]

... Kirby Vacuums

Kirby Sentria I just got done usting the carpet shampoo system and now my Kirby wont start

When you replace the outer bag assembly, you have to make sure that it is turned clockwise untill it fully stops. There is a small switch on body of the Kirby that is only engaged when the bag assembly is installed correctly ... Kirby Ultimate G Bagged Upright Vacuum

Kirby g5d will not shift into drive - Kirby G5 Bagged Upright Vacuum

Check tech drive sensor, where handle connects to main unit, but you need to open cover off and greese handle slider. ... Kirby G5 Bagged Upright Vacuum

Kirby drive selector - Kirby Ultimate G Bagged Upright Vacuum

Go here > http://www.goodvac.com/kb_results.asp?ID=16 ... Kirby Ultimate G Bagged Upright Vacuum

My kirby sentria won't go into drive - Kirby G5 Bagged Upright Vacuum

... Kirby G5 Bagged Upright Vacuum

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

My kirby is shorting out when i plug it in and turn it on it wont turn on and then after a little bit it will turnon but twhen you move it it will turn back off.. and there were sparks from the cord.... i was wondering if i still have a warrant to get another one ive never had a problem with my kirby i love it but am dissapointed that i cant use it

... Kirby G5 Bagged Upright Vacuum

Kirby vacuum stuck in drive mode - Kirby Vacuums

... Kirby Vacuums

Tray wont stay connected to kirby - Kirby Ultimate G Bagged Upright Vacuum

Here is a guide for the shampooer...follow it exactly and it should help. Please remember to rate it if it's helpful! :0)\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Drive lever the neutral/ drive lever does not engage. seems loose. I have open up the bottom of gear area and have a loose bracket,how does it go back together, need a parts diagram?

Assembly instructions (lots of pictures) HERE. ... Kirby Ultimate G Bagged Upright Vacuum

My kirby wont start - Kirby Vacuums

Check the plug,then check the switch. ... Kirby Vacuums

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?

Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.

HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

The belt on my Kirby G3 wore out, and I bought replacement belts from two different sources--one an official Kirby supplier and one a store brand. Neither belt is long enough to catch the belt lifter when it is rotated and to reach the drive shaft.

Kirby has only had 1 belt from day one. sometimes you do need to push the belt up to catch the belt lifter ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0560 seconds