Having problems with your Kirby Generation 3 Bagged Upright Vacuum ?

Our G3 Kirby will not power up?

\015 Plugged in (verified power source) pushed the power button and nothing happens.\015

Answers :

Either the cord or the switch is bad. The cord is simple. Take the tab screw on the back of the machine off and the screw holing the cord cover off. Pop off the cord cover un-plug and remove then reverse steps to replace. If it is the switch that is better left to proffesionals so call your local vacuum shop.
Repair Help & Product Troubleshooting for Kirby Generation 3 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby vacuum I have a G 6 kirby vacuum. The power cord has been checked and has continutity and replaced the power switch and the vacuum will still not run


There are 2 safety switchs, one on the front that the nozzle activates, and one on the side that the bag asembly activates. The motor brushes and/or armature maybe bad. ... Kirby Ultimate G Bagged Upright Vacuum

My Kirby G5 has a power problem. Its handle needs to be tiltled all the way to almost flat position for the power to comne on. If the handle is back up to its standing postion, the power will be off. What's the cause of this problem? Any suggestions/comments will be greatly appreciated!!!


Sounds like u may have a problem with the cord connection inside the power plant would suggest u take to repair shop not something i would suggest u try yourself ... Kirby G5 Bagged Upright Vacuum

Kirby G6 no power


Could be the switch, I would check the cord 1st. It has 2 wires running thru it, one may be open. That power cord goes bad often, if anyone is pulling on the wire rather then the plug, then it would have have stretched and break. ... Kirby G6 Bagged Upright Vacuum

No power kirby sentria wont power up no sound or light nothing


There should be an onboard fuse for the Kirby vacuums. Look on the bottom of the motor. Hope this helps. ... Kirby Ultimate G Bagged Upright Vacuum

I have a Kirby Generation 3 that will not power on with the Carpet Brush attachement BUT will power on with the hose attachment. Please advise. Thanks


Make sure everything is lined up and and bag is fully attached. If it does not work after that, you could have a defective safety switch. Take it you an Authorized Kirby Dealer. Don't pay more than $40 for this repair. ... Kirby Generation 3 Bagged Upright Vacuum

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit


Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

We bought our Kirby less than 5 years ago and lately are not happy with it....it keeps breaking. The warranty has expired and our biggest complaint is that it has lost it's suction power. All the contents stay in the hose when I vacuum out the car or upholstery and it does vacuum well at all. The Kirby store quoted us over $200 to fix/ service it. Apparently this is not covered in the free yearly maintenance which we just had done. Any suggestions?


\012 Hi there,\012Well I do have a suggestion though you may not like it use it as a boat anchor.....no no I am just kidding. I have sold vacuums for 20 years and Kirby has b ... Kirby Ultimate G Bagged Upright Vacuum

On a Kirby sentria the metal spool sticking out that goes into hose or power head becomes extremely hot and left burns marks on brush tube. It only gets hot when using power head. I checked all adjust


Check the brush roll to be sure it's spinning free too much drag can cause that to get hotter but usually it would break the belt. That spindle will get hot from the friction created by turning the belt and from the motor's heat. They'll just get hot ... Kirby Vacuums

How do i know if my power button is not working on my diamond edition ultimate g kirby vac? It was fine when i changed the water and went to turn back on it does not power on, neither will the button click. please help


Make sure the water reserve all the way on it may not be cliped on all the way ... Kirby Ultimate G Bagged Upright Vacuum

I currently own a kirby heritage II, and love the cleaning power it has, but....it is becoming harder and harder for me to manuever it, do to arthritis. Are the newer kirby's any easier? If so, how much? If not, what vacuum would you recommend for me?


If you are good and familiar with a Kirby, the new generations are self propelled with a transmission BUT may cost you over $1500 US. They will be very familiar but easier to push, yet still vastly overpriced. You might want to look for a deal ... Kirby G4 Bagged Upright Vacuum

Kirby sentria does not have suction - Kirby Sentria 192006 Power Cord


... Kirby Sentria 192006 Power Cord

No power There is no power to my kirby G5. I have checked both safety switches and they seem to be operating properly. I think its the switch but I'm not sure.


Where would the reset button be? ... Kirby G5 Bagged Upright Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.


The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

Kirby G5 - the Tech Drive does seem to have much power


You need either a new nutreal cam bracket assembly, that is what engages and disengages the tech drive.OR to adjust the handle pivot assy- diffucult . this is not for the faint of heart. it is possible to fix them as i used to repair kirbys, howeve ... Kirby G5 Bagged Upright Vacuum

Kirby Diamond Edition (no power)


Try my troubleshooting guide....\015\012\015\012http://reviews.ebay.com/COMMON-PROBLEMS-WIT ... Kirby Ultimate G Bagged Upright Vacuum

The kirby wont start no power


... Kirby G6 Bagged Upright Vacuum

Kirby G6 - won't power on


Check the cords two wires with an OHM meter for continuity replace if you get a reading showing OL The ground wire you can forget about this test\012 If any sort of numbers appear in the meters display the cord is good\012Replace the swit ... Kirby G6 Bagged Upright Vacuum

Green light on power nozzle of Kirby vacuum, Model G7D


The green light is just to inform you that the brushroll is spinning. there is a magnet on the brushroll that makes the green light come on every time it rotates. also why it looks like the light flickers because the magnet only makes contact once pe ... Kirby Ultimate G Bagged Upright Vacuum

REPLACING THE KIRBY POWER SWITCH


... Kirby G4 Bagged Upright Vacuum

Kirby g2000 no power


This video should help you ... Kirby Ultimate G Bagged Upright Vacuum

Kirby won't turn on only when trying to use power nozzle


Make sure that your power nozzle has a little metal prong that plugs into the little rectangular hole in the fan case. If the prong is broken, you'll need a new nozzle. If the prong is intact, you'll need a new switch. Here is a link to help with the ... Kirby Ultimate G Bagged Upright Vacuum

Kirby Generation 3 no power...


I don't believe there are any service manuals online, as Kirby has service centers around the country. There are 3 things in the power string--on/off foot switch, the power cord, and the power assembly that the cord plugs into underneath the bag in t ... Kirby Generation 3 Bagged Upright Vacuum

Kirby ultimate power off


Make sure the bag assembly and either the power nozzle, or hose attachment are correctly attached. The kirby has safety swithes that are only engaged when these components are correctly installed. They look like small resessed buttons on the base u ... Kirby Ultimate G Bagged Upright Vacuum

No power from Kirby!!


Determine if the headlight works before anything else. If the light works but the motor won't you have power thru the vac and the problem is internal possibly motor brushes... or a loose wire on the inside connecting to the switch. If the light ... Kirby Ultimate G Bagged Upright Vacuum

My Kirby vacuum wont power on


Check for power at your brushes, possible worn brushes in the motor ... Kirby G6 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0417 seconds