Having problems with your Kirby Generation 3 Bagged Upright Vacuum ?

I have a Kirby Generation 3 that will not power on with the Carpet Brush attachement BUT will power on with the hose attachment. Please advise. Thanks


Answers :

Make sure everything is lined up and and bag is fully attached. If it does not work after that, you could have a defective safety switch. Take it you an Authorized Kirby Dealer. Don't pay more than $40 for this repair.
Have to make sure its in the slots will not power unless lined up
Repair Help & Product Troubleshooting for Kirby Generation 3 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kirby Generation 3 that will not power on with the Carpet Brush attachement BUT will power on with the hose attachment. Please advise. Thanks


Make sure everything is lined up and and bag is fully attached. If it does not work after that, you could have a defective safety switch. Take it you an Authorized Kirby Dealer. Don't pay more than $40 for this repair. ... Kirby Generation 3 Bagged Upright Vacuum

I don't get not power after attach the hose? - Kirby Generation 3 Bagged Upright Vacuum


Bad power switchSwitch is designed to run motor on higher RPM when hose is connected. The high speed lever mechanism failed and you need the new switch. You can find it ... Kirby Generation 3 Bagged Upright Vacuum

I recently lost power to the power head. Thinking the hose was not sending current to the head, I bought a new hose. It did not solve my problem. I have since noticed that a warning symbel is appearing that indicates what looks like a key with TA inside. The vacumn has good suction. Please advise John.


Hi\015\012\015\012Please check the link bellow to diagnose your problem…..\015\012\015\012http://home.howstuffw ... Electrolux Epic 6500 Vacuum

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition


Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN


First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

When i use the power brush attachment, dust flies out of the hole that the hose attaches to... is there a way to prevent this or is it just how it works?


This is the nature of this vacuum, the roller will always spin, when the vac is turned on. You can either cover wit tape or maybe find a sock to put in it (remember to remove sock) when putting hose back ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

On a Kirby sentria the metal spool sticking out that goes into hose or power head becomes extremely hot and left burns marks on brush tube. It only gets hot when using power head. I checked all adjust


Check the brush roll to be sure it's spinning free too much drag can cause that to get hotter but usually it would break the belt. That spindle will get hot from the friction created by turning the belt and from the motor's heat. They'll just get hot ... Kirby Vacuums

My Kirby vacuum lost most of its suction. .. The hose attachment is clear, the brush attachment the same.


... Kirby G6 Bagged Upright Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

The red light with an exclamation point is lit and vacuum won't turn on. This happened as I was attempting to change to the brush power head. We've just moved and I can't find the manual. Please advise. Bonnie


... Miele Vacuums

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

How do you attach the belt for the roller-brush on a Kirby Generation 3, up-right vacuum-cleaner?


Greetings,\015\012\015\012Please see the attached video on how to replace the belt on a Kirby Generation Vacuum Cleaner. This is an easy to follow step by step direction on the proper way to replace the belt, as well as do basic mainten ... Kirby Generation 3 Bagged Upright Vacuum

Where do you connect the attachment hose? - Kirby Generation 3 Bagged Upright Vacuum


You have to remove the brushroll nozzle and your attachment hose goes in its place set it on the cross rail, rotate up and lock in place. ... Kirby Generation 3 Bagged Upright Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.


Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david


Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

Can you tell me if Powermate Power Brush attachments are all the same for all the Sears Powermate Cannister vacuums.  That is, would one power brush attachment on a Model 116.56512690 fit one that is Model 116-22512202?  Are the connecting ports all the same size?Thanks for your help.


I think your confusing model #s ,as the 116. 22512202 is the canister model number and the model number of the powerbrush attch would be 116.52512202,but to answer your ? no it depends on which wand your useing that determans which one you can use ... Kenmore 22812 Bagged Canister Vacuum

My Kirby Sentria upright vacuum won't turn on since I disconnected the hose attachment


... Vacuums

Kirby Ultimate G will not suck with main brush head attachment


You need a new belt. When the green light goes out, the brush is not spinning. The belt is stretched and needs replaced. Here are detailed belt changing instructions....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto


Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

I have the Eureka The Boss Power PLus Model # 4703 Type A. When using the detached hose and wand it works OK; however, when using the Vacuum with the hose attached it doesn't work well at all.


... Vacuums

Kirby turns on with hose attachement but not with head attachment


Front of the unit, black switch that is pressed by this plastic protrusion from hose coupling has two parts. It is because ANY generation Kirby has speeds - HIGH for vacuuming with hose and LOW for using it with nozzle.Looks like the switch we ... Kirby Ultimate G Bagged Upright Vacuum

I have the bissell powerglide vacuum with the turbo brush attachment. Being the neighborhood "cat lady", I love this attachment -- that is, I did until it just stopped spinning. I don't see anything blocking the brush. It just doesn't spin when I attach it to the vacuum hose.


1. this could be (2) things that are happening or 32. there is hair surround the spindle (rotation) brush tool blocking rotation or you have a motor that has failed and it is not turning the rotation brush.3. the switch (on /off) has fail ... Vacuums

Power shuts off when hose is attached. runs without hose attached. bag is empty, hose is cleared.


... Electrolux Epic 6500 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0830 seconds