Having problems with your Kirby Generation 3 Bagged Upright Vacuum ?

I need to remove the top of the motor unit on a Kirby Generation 3 to access the motor area of the vacuum

Answers :

First remove the back, then remove the handle assembly. Then pop off the plastic switch cover and it has one screw on the back you will need to take out, then there are two screws in the front of the body housing and two on the back that you will need to take out and then you are ready to take the top cover off and get into the motor area.
Repair Help & Product Troubleshooting for Kirby Generation 3 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to remove the top of the motor unit on a Kirby Generation 3 to access the motor area of the vacuum

First remove the back, then remove the handle assembly. Then pop off the plastic switch cover and it has one screw on the back you will need to take out, then there are two screws in the front of the body housing and two on the back that you will ne ... Kirby Generation 3 Bagged Upright Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??

... Kirby Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I need to replace the agitator belt on a Hoover Elite U4465-9 upright vacuum cleaner. I have removed the bottom cover, but there is no access to the motor spindle to loop the belt around. How do I do this?

... Vacuums

Need to access motor on Volta Ultima 2000W vacuum cleaner

... Electrolux Guardian Bagged Canister Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!

Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?

... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that

Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and sh ... Beam Industries 2900 Serenity Plus Central System Vacuum

Thank you for the detailed explanation regarding the kirby vacuum functions, but we would like more information about the exact shampooing instructions. in explanation we would like to know exactly what solution and in what quantity to apply first to the fabric... how long we need to let it soak in.... and how to remove the stains using only our kirby vacuum witjh shampoo attatchment from start to finish...

... Kirby Ultimate G Bagged Upright Vacuum

My Filter Queen just started making noise from the motor area, it was very hot. Upon removing the top thing that covers the area where the air blows out, there were sparks and it smelled pretty bad. My guess is the motor is shot. Is this difficult to change?

The motor will need either a rebuild with new bearing, or replacement. Parts should be no more than $100 .EASY project. 20 minutes max fro a pro shop. If you can tie your shoes you can do this one yourself. If replacing, upgrade to a ball/ ball ... Filter Queen Majestic Canister Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.

... Sanyo Vacuums

BURNING SMELL My DC 07 has suffered from poor suction in the upright position for some time now but this morning it ground to a halt. It was if the motor had burned out. I turned it upside down and some small stones etc tumbled out. I tried switching on again and the motor kicked in but the smell was horrendous so i switched off immediately. If it's likely to be **** inside the motor area i don't no how to access it. I've removed for fixing screws but still unable to prise apart. Is it just the

Hi.\015\012\015\012Try this site http://dysonmanuals.llc.nu/ has service manuals covering removing the Dc07 motor. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?

... Bissell 8910 ProHeat Clear View Upright Vacuum

Need Kirby Generation 3 Vacuum cleaner manual. Vacuum is not picking up dirt from floor. Seems to have enough suction to inflate the bag, but when you check the suction under the vacuum, there seems to be extremely litle suction.

If your brush roll is turning and your bag is not overly full, then the only other thing it can be is a clog where the bag connects to the vacuum. Turn the plastic part out away from vacuum and lift off to see if you have something clogging it. It ... Kirby Generation 3 Bagged Upright Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?

Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I have a samsung SC7800 (smart wing system) vacuum cleaner. I think the impeller is jamed with sawdust. I have removed the part than holds the removable filter, but can't see how to remove the reat of the top case to access to impeller housing. Does anyone know how to do this or where I can view a repair manual for this model?

Unfortunately these tend to break frequently.... You might be able to get a wiring diagram at www.wize.com Good Luck!! ... Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Our plug got pulled out (by driving away while the canister was still plugged-in after a vacuuming the car). How can we open up the unit to reattach the wires? We accessed two sets of screws (2pairs) toward the bag-end (not the motor-end) of the canister, but we can't locate any access for the two other apparent screws inside the body.

Remove all visible screws. Top and bottom, then once they are all removed, take a flat-head screwdriver and slowly pry around the canister until it comes completely loose and can be removed. Then you should have access to the wires which can then be ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1770 seconds