Having problems with your Kirby Generation 3 Bagged Upright Vacuum ?

Kirby generation 3 fan

\015 How do I seperate the fan from the motor on a kirby generation 3 vacuum? Thank you.\015

Answers :

You have to take off the top cover, then the handle pivot. Look down at the back of the armature you will see that it has a flat spot, you use a small vise grips or pliers to hold it, turn the belt pulley to the right if I remember right and turn the pulley off. If it won't come free, use a couple of flat blade screwdrivers and pry up to pop the fan off. Then put it all back together.
Repair Help & Product Troubleshooting for Kirby Generation 3 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby generation 3 fan


You have to take off the top cover, then the handle pivot. Look down at the back of the armature you will see that it has a flat spot, you use a small vise grips or pliers to hold it, turn the belt pulley to the right if I remember right and turn th ... Kirby Generation 3 Bagged Upright Vacuum

How to install Kirby g4 fan - Kirby Generation 3 Bagged Upright Vacuum


It needs to be stripped completly down, if you are confident at doing this then here goes.\015\012It has been a while for me so take your time and some of the steps may have to be completed slightly differently.\015\012Isolate / unplug t ... Kirby Generation 3 Bagged Upright Vacuum

Replace fan blade e77491 - Kirby Generation 3 Bagged Upright Vacuum


KIRBY VACUUM REPAIR HOW TO REPLACE THE FAN IMPELLER ... Kirby Generation 3 Bagged Upright Vacuum

How do you get to the fan on the generation 3 kirby


First remove the handle, next remove the screws attaching the cord, and switch trim plate. The small screw and knob on the handle pivot must be removed to remove the switch trim piece - insert a flat screwdriver into the small slot in the plastic and ... Kirby Generation 3 Bagged Upright Vacuum

Kirby Generation 3 Drive spinning backward.


Just take it into kirby. ... Kirby Generation 3 Bagged Upright Vacuum

KIRBY G4 FAN ASSEMBLY ORDER


First put the gasket on the spacer, thin end to to out, push it down all the way on the motor shaft, then put the nylon washer on, then the fan, metal washer and then the pulley, just snug it, (don't tighten too much just beyond hand tightening). Pu ... Vacuums

Fan and bearing replacement on a Kirby G6


If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

Kirby Vacuum Fan


The pullet is what holds it in place, if it has come loose, just tighten it. But if that doesn't help, then replace the fan. ... Kirby G6 Bagged Upright Vacuum

I have a Kirby Generation 3. The handle spring assembly is broke, so I took it apart to get a part number. Can you tell me if there is a cross reference or something on these parts. I am unable to find a part with the same number that is located on the part I took off. The number on this spring assembly shows Kirby HA-670289B K-1. Any help finding this part is appreciated.


... Kirby Vacuums

Kirby g6- How do you replace the cord? - Kirby Generation 3 Bagged Upright Vacuum


I do believe o6 the cord goes in to the metal housing of the motor .They are usually held in by a rubber grommet and they can with some patience and force be pulled out slowly does it as you don't want the wires ... Kirby Generation 3 Bagged Upright Vacuum

Kirby G3 made loud noise when running. Sprayed silicon in fan thinking it might be a bearing. Found a coin and nail in fan and removed. Tha vacuum would not turn on. Replaced switch and brushes. Still nothing. Did the silicon spray do something?


No - the silicon is an insulating material and would have no effect on the electrics of the vacuum. Most likely you have a bad connection - dismantle the vacuum again and check the wiring and the motor with an ohmmeter. Be very attentive with the bru ... Kirby Generation 3 Bagged Upright Vacuum

How much horsepower for a Kirby G3 - Kirby Generation 3 Bagged Upright Vacuum


All kirbys are good, i reccomend getting a G6 ... Kirby Generation 3 Bagged Upright Vacuum

I need to replace the fan blades on a Kirby Heritage II, Model 2HD, vacuum cleaner. How do I remove the drive shaft that the fan is mounted on? Thanks, Robert Croft


... Vacuums

How do I assemble kirby g3 carpet cleaner? - Kirby Generation 3 Bagged Upright Vacuum


Greetings,If you click the link below it will take you to a video demonstration that explains step by step what you need to do to convert your Kirby into a carpet shampooer. The vacuum in the video is the Kirby Sentria, but the procedure ... Kirby Generation 3 Bagged Upright Vacuum

Replace Kirby legend II fan (impeller blade) - Kirby G4 Bagged Upright Vacuum


In order to replace the fan you will buy a 2 or three piece lexan fan kit containing the fan a spacer and shaft. You must remove the carpet head and then looking from the back of the machine you will find a series of philips screws on the oute ... Kirby G4 Bagged Upright Vacuum

How to set up kirby to vacuum mattress - Kirby Generation 3 Bagged Upright Vacuum


Detach lower end of bag from body of vacuum.\015\012Attach hose to the opening.\015\012Attach above floor tool for vacuuming.\015\012\015\012See video instructions on below site.\015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum

How to replace kirby generation 3 switch? - Kirby Vacuums


I am a trained professional with all the tools & experience and this is a job that would take me 2 hrs. Do your self a favor and take it to your local vacuum shop.It'll probably run you around 200 dollars , half parts and half labor. You pr ... Kirby Vacuums

Bad fan how to remove fan on kirby heritage 2 legend vacuum cleaner.


There might be latex sealant around the perimeter of the fan casing. This was the case with my G3. The latex sealant prevents dust from blowing out of the fan "chamber" while it's running and under positive pressure. And as reddevil16 said, the spind ... Kirby Ultimate G Bagged Upright Vacuum

Kirby Hello, I have a generation 3 kirby- it was working - I turned it off & it will not turn on again - is there a safety switch /reset button or did the on/off switch go out - I have had it 15 years & replaced the switch 1 time - Thanks


You either need a switch or a cord. Check out my troubleshooting link which includes links to do-it-yourself guides and parts.\015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum

Broken fan need a repair man or service centre. If not a replacement fan for self repair. I live on the Gold Coast Ray is my name. Kirby Legend 1 model 2HE


Http://www.ultimatesanitarysupply.com/pdfs/VacuumMaintenance.pdf\015\012\015\012see the link ... Kirby Vacuums

How to change the fan in kirby heritage 2 - Kirby Heritage II Vacuum


This site has a great tutorial on how to do it. I did it myself and it worked out great. Get the parts online or at your ... Kirby Heritage II Vacuum

My vacuum kirby turned by itself - Kirby Generation 3 Bagged Upright Vacuum


The problem was that the piece that you connect to the wall outlet was broken. I purchased a new cord and it is working fine now. Thank you! ... Kirby Generation 3 Bagged Upright Vacuum

Kirby Heritage II 2HD Vaccum Cleaner. I have removed the housing and reached the motor shaft for the vacuum fan. How do you remove the fan from the shaft.


Hi, you can visit this site to view how to remove the fan from the shaft...http://www.diyonline.com/servlet/GIB_BaseT/diylib_article.html?session.docid=1678Take care ... Vacuums

Kirby g3 upright will not pick up trash - Kirby Generation 3 Bagged Upright Vacuum


... Kirby Generation 3 Bagged Upright Vacuum

I need a manual for a kirby vac gen #3 - Kirby Generation 3 Bagged Upright Vacuum


Click the link below for the manual It's a very large .pdf file, so just be patient while it loads;http://kirby.110mb.com/docs/kirby_sentria_manual.pdf ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0321 seconds