Having problems with your Kirby Generation 3 Bagged Upright Vacuum ?

Generation 3 vacuum. I need to know how to repolace the Kitrby Belt. The video online shows the Sentria, but that has not helped me. The problem I have is the arrows and tightening the belt. Thanks, Gene Paul


Answers :

The arrows should point in the normal running direction of the belt. If you have the correct belt, tension should not be a problem as it is stretched during placement of the sweeper head. Start the motor for a moment with the motor shaft exposed to determine belt rotation direction. Check the bearing ends of the brush to make sure they are free of debris, and that it spins freely with the belt off. Hope this helps!
Repair Help & Product Troubleshooting for Kirby Generation 3 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Generation 3 vacuum. I need to know how to repolace the Kitrby Belt. The video online shows the Sentria, but that has not helped me. The problem I have is the arrows and tightening the belt. Thanks, Gene Paul


The arrows should point in the normal running direction of the belt. If you have the correct belt, tension should not be a problem as it is stretched during placement of the sweeper head. Start the motor for a moment with the motor shaft exposed to d ... Kirby Generation 3 Bagged Upright Vacuum

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped


... Electrolux Guardian Bagged Canister Vacuum

Dear sir, i needs a solution for chinese nokia 6300 mobile's white screen problems so help me how i can solve this problems please.......... fast help me sir. thank you


Remove the memory card and battery replace batterry after 30 minutes to hard reset. If the phone boots up then check card for errors, virus, delete, format as required and reset.\012If this wont solve , you will need help fromNokia care to rein ... Vacuums

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I am located in Trivandrum. I have a britelite " Impact Halogen" torch bought from Dubai two years ago. Recently, have problem in recharging. When I recharge it - not getting recharged. Immediately it gets down the light.Then I have changed the Cell and it worked for sometime and agin the same problem arise. Could you help me on this.


... Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

I have an elna 3007 machine. Our service man died and I need help with the tension. I can't get the top tension number to change off zero. when I free motion, all I get are loops top and bottom. I have adjusted the machine the best I can but still have the problem. I'm in the middle of a quilt and could use some help.


... Elna Vacuums

Low suction Replacing filters....need help replacing the belt - anyone know how? But before doing these things, have had a problem with suction....I'll let you know if the problem clears up.


Hi, You can take care of both things at once. Here's how:\015\012Unplug and flip your vacuum over, beater bar side up. Remove the cover base plate that surrounds your beater bar. It's held on with either clips or screws, and usually "hinges ... Eureka 2961AVZ Bagless Upright Vacuum

Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???


Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum

We have a GE Advantium 120 microwave. all sounds like the unit is working all controls work. it does not heat at all. I have the shelds off and do not see any problems. what do you think is the problem and how do I test for it? thank you for your help.


If the unit works but it doesn't heat then the magnetron isn't working. The only way t test it is to measure the 2 voltages that power it: the heating coil - 5 volts AC and the high tension - 5000 volts DC. While you can measure the heating voltage ... GE Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks


If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?


Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

I've recently bought a hitachi HDR505 & haven't had a problem using it with an indoor ariel other than the fact in bad weather conditions there have been problems with the signals. So I tried to attach the ariel wire that connects from a box in the corner of my living room which connects to the outdoor ariel but cannot connect it into the 'ariel in' compartment on the box as it does not fit into that hole but does fit into the 'ariel out' hole. Please could I get help with a solution asap as I w


... Hitachi Vacuums

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]


Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I have a Hoover Wind Tunnel that has been used twice both times at Christmas to pick up pine needles. It really has never been used because my cleaning ladies come every week and use their own machine. The problem I have is that the machine just doesn't pick up anything. Can you help. It's not overuse that is the problem!


You may have the ductwork of the cleaner plugged up with the pine needles. First, unplug the hose from the cleaner and find if you have suction into the bag. If so, check the hose and ducts for blockage from the pine needles. ... Vacuums

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help


You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

I purchased a used Minuteman 2400 series buffer/burnisher over the weekend from a store that is closing. The unit is about 7-8 years old. I did not get a manual with this item, can you help me out with this. I would like to read up on it so if I have problems I can look back on it. Even as far as the operation of it would help to have a book for it. Linda


I have this manual available via email. chris321 at gmail. ... Vacuums

Hei, I have sewing machine Brother NV500D and got technical problem need to be service/repair. I'm now in Malaysia and don't have techinical/repair service for sewing machine NV500D. This is overseas model. In sewing machine screen display 'F04'. The problem automatic needle not function and part missing. I dont no how to fix this. Can't i got the instruction manual service picture if i can't fix own. please help me. thank you.


... Vacuums

The vacuum won't turn on. We've tried multiple outlets with the same problem. We've cleaned the filters, which caused it to turn on once, but a week later the problem occurred again. HELP!


I have this vacuum and mine would not turn out and it turned out to be the top half where the power switch is located was not aligned properly. I ended up putting a new screw in, but before I could see where the vacuum was not aligned and would just ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Hi we have a model 31075 which i did not find in the list im hoping it's similar to the 31079 The problem is that the agitator has stopped working and i can not open it to find the problem is there a manual available or a site i can go to. Can you suggest what i can do to open it to look around I am very handy with most things but this thing has got me frustrated at this point. thanks for your help. Regards Chuck


... Kenmore 31079 Upright Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

Hi i hae a star product whipper sniper and i cant get it to go i hae spark i hae fuel but it seems as if there is no fuel getting to cylinder i think it is a problem with my carby the serial no is fcb12071 please help rectify my problem cheers


One thing that you can try is to remove the carb from the unit and spray it down with carb cleaner -- maybe it is blocked (?),,, one more thing to try would be to see if it will fire using ether. there could also be something wrong with the fuel dia ... Vacuums

Greetings - my Dyson DC41 animal vacuum seems to be having problems with the ball - the right side of the ball if you were to be standing behind the machine seems like it's tightening as it rolls forward, as it tightens its harder to push the machine forward. Any thoughts, any fix it ideas? Thank you.


... Vacuums

How do I replace the hemp filter? Is there more than one? of course I've misplaced owners manuel, I've had it since July 2010, live where there are 3 indoor cats, I'm allergic to cat dander, for the first few months no problems with vacuum stirring up dander, however now, when vacuuming, my lungs start to close up. Definitely problem with the filtering system. Help! Today is 3.22.11, it's 11:24 am. Thank you.


... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0474 seconds