Having problems with your Kirby Generation 3 Bagged Upright Vacuum ?

The neutral wont work

\015 Will not go into neutral, wont go out of drive\015

Answers :

You will need kirby engineer to fix this. contact your local agent or see kirby.com
Repair Help & Product Troubleshooting for Kirby Generation 3 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The neutral wont work

You will need kirby engineer to fix this. contact your local agent or see kirby.com ... Kirby Generation 3 Bagged Upright Vacuum

My Brother XL4030 wont swtich from bobbin winding to sewing - bobbin winding works but when i switch to sewing just wont work

... Vacuums

Pickup water wont pickup the water after putting it down very little comes up into the tank .it worked fine when we baught it but after not useing it for some time it worked now it wont **** water up at all can anybody help.

The clear shroud covering the front of "hood" has two sheet metal type screws at the bottom in front of the brushes, these two screws also hold the little straight brushes ( one on each side) in place. I found one of these screws had broken it's plas ... Hoover F6020-900 SteamVac Upright Vacuum

DC07 brush wont spin on bottom, took all apart and wont work

Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum


Inside the clipers there is a spring switch,,its broken? or all the vibration in the clipers has shook a wire off inside,,,in short its time for a new set of clipers,, ... Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

Wont spray i have a bissell pro steam 2x and it wont spray the water out, i have cleaned everything and nothing seems to be working ...please help

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

Re UH70040W seriesZF12.0.I can't seem to get the brushroll agitater to work it just stays off and the brushroll does'nt work the belt that drives it wont grip the roll? It's brand new!

I followed the instructions,you have to release the handle as though you were vacuuming and it works automaticly you can't put it on ON when it's upright!! Duh ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks

If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

My bissell vacuum attachments wont work, as soon as i attach anything besides the crevice tool it wont ****,but sucks fine when its just the hose

Tern upside down remove plastic cuvier look wear the hose gos fillip skew driver ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a eureka altima bagless and it wont pick up dirt i clean it and everything it just wont work

The belt is probably worn, stretched or broken that is why it is not picking up. Here is\015\012a link to the owners manual which has instructions and a link to the\015\012belt you need. ... Eureka Capture Upright Vacuum Vacuum

My McCulloch whipper snipper was working just fine after finding cracked fuel lines,. Replaced wiht home made lines and worked fine until Sunday and now wont start at all . Checked everything , now think its electrical Would like to kow if there is anyone in Perth who can sort this out

Your local lawn mower repair shop will be able to fix it for you. ... Vacuums

My dyson works with the hose but wont work the normal way

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My suction wont work. It works for about 2 swipes and then quits. When you stop and restart it does the same. It is only 2 months old!!!!!

Hopefully you don't have a bad impeller on the suction motor. Start with this though: Make sure that you check for obstructions in ALL of the tubes, from the brushes all the way to the bag/canister. I've found that in many cases, especially if you ha ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My bissell proheat carpet cleaner wont turn on. Its plugged in and everything but wont turn on. I've had it for a few years but its always worked before. Do they have to heat up if I haven't used it in a while?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My shop vac stopped working while vacuuming i looked at everything i could look at and still wont work tried several other outlets checked cable still nothing

Staring from the failrue of the power cord,the main plug,t he main switch each of the sections must be tested for continutiy before we can conclude.\012SInce it is clear case of power failure the voltage must reach the motor,if not back trace t ... Shop Vac Vacuums

GE on/off timer for a bathroom fan - switch has four wires Green - ground White - neutral Black - power Blue - lead My fan has two - white neutral and black lead I have tried every configuration and cannot get the fan to work. Any suggestions?

I would guess that the black wire on the timer is the power in and blue is the power out to the fan (hook it to the black wire going to the fan) The other colors are right. ... Vacuums

The switch on and off wont work so i took it off and it works but know iam having problems putting it back together the spring are the problem

Those springs are tricky to get back in. you can use the flat end of a screwdriver to hold them down and compress them. I would recomend taking it to a proffesional to get it put back together right before you break the plastic and cost yourself some ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.

It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The hand-held wand wont slide back into the tube. It wont go down far enough to click in and become the handle again. It was working fine but all of the sudden won't fit back in.

Sounds like the tube has something inside of it that is obstructing the path. veriffy the the "female" end of the tube isnt obstructed, and also, make sure that nothing is bent ( which can happen easily). use a flashlight to shine down into the tubes ... Dyson Ball DC24 Bagless Upright Vacuum

How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin

The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Scuncii Steamer wont work wont blow steam anymore

It is probably clogged with rust or limescale - can happen with steam cleaners. Sadly there's no way around this but to try a limescale remover in distilled water such as Calgon limescale remover. Fill the kettle as normal and give it time to boil up ... Scunci 52067 Handheld Steam Vacuum

Why doesnt my Dyson auto adjust on our carpet? We have a taller, soft carpet and it digs into it, making it very difficult to vacuum. We have had the vacuum for about a year at another house and it worked GREAT on the berber......our new has a tall carpet somewhat like shaved berber and now the vacuum wont work.

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a bissel proheat 2x and everything works on it except the bottom sprayer. I cleaned everything out on it and everything is in place but it wont spray. Can someone help me through this to get it working?

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0518 seconds