Having problems with your Kirby Generation 3 Bagged Upright Vacuum ?

Belt problem My belt broke. I put a new belt in, followed the instructions, seemed to be right but as I started using the vaccuum, it starting smelling like burnt rubber. The belt was extremely hot. Took it apart, tried again and the same thing happened. Please help me!!!!


Answers :

Get the old lady to use a dustpan and brush instead SORTED
Here is the link to the detailed instructions for belt changing. When you take the brushroll out, make sure that the brushroll spins freely. If it doesn't it will burn up your belts and needs to be replaced.

http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4-G5-GSIX-ULTIMATE-G_W0QQugidZ10000000003720039

Hope this helps...
Marci
Repair Help & Product Troubleshooting for Kirby Generation 3 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Belt problem My belt broke. I put a new belt in, followed the instructions, seemed to be right but as I started using the vaccuum, it starting smelling like burnt rubber. The belt was extremely hot. Took it apart, tried again and the same thing happened. Please help me!!!!


Get the old lady to use a dustpan and brush instead SORTED ... Kirby Generation 3 Bagged Upright Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I am trying to get to the belt on my fantom cyclone xt, although I am unable to see any screws to remove. I took the rubber bumper off thinking this would be of some help although nothing there either. Can you help???????


Remove the lens covers, bulbs and the foil. under the foil are two screws. remove the screws and the cover lifts off. the motor for the belt is held in with one screw. ... Fantom Vacums Cyclone XT Upright Vacuum

Have a rexair model D series vacuum cleaner that worked fine until recently. Started making noise and then started smoking/overheating. I took apart the machine cover and am unsure how to get it tore down to see the motor or belt in there. Please help!


Below I have listed a link to the manual that has instructions on how to change your belt and a link for the replacement belt you need. ... Vacuums

Euro-Pro EP961 Professional Steam Cleaner Hi, The on light stays on but nothing happens. You can't shut it off. I took apart the switch and the connections look burnt. Please help! This is the best product we ever purchased!! Thanks, Diane Elsner [email protected]


... Euro-Pro Vacuums

Im trying to put the peice back together that goes under the tube that hold the water the part that goes into the hole in the vacum.. i took it apart because its not spraing right to see if it was cloged.. and now im not sure how it goes back together.. can you please help me.....


I tried to find a service manual for this, but came up with only a exploded view diagram:\015\012\015\012http://ineedbags.com/images/b8920.jpg\015\0 ... Bissell 8920 ProHeat 2XTM Upright Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Changing belt Please advise how to change the belt. I wasn't the person who took the belt off, didn't watch. Now it's just me and the belt. I had 2, but 1st one burnt right off. Apparently I didn't have in the right spot! don't want to waste the only other new belt I have. Pictures would be greatly appreciated!!!!!!! Thanks Tammy Can call 920-660-0680


Step 1: Lower handle to floor to change belt Step 2: Remove the two screws from the top hood on the footStep 3: Lift hood to remove Step 4: Lift right end of brushroll (the belt end) Step 5: Remove and discard belt.Step ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

A small belt fell from underneath my bissell steam cleaner and I notice the brushes no longer rotate when I purchase the part where does it go? I tried turning it up side down to find out where it came from don't know because there is a compartment for the belt access but that particular bet is not broken. It's a very thin belt I can not make out the number located on the belt please help.


If you are unsure about where it goes it may have a diagram in the owners manual. When you say you saw a belt in a compartment are you sure that it is not an extra belt you are seeing as they often give an extra in the machine kept in a compartment l ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!


... Hoover Vacuums

I have the Bissell upright cleanview bagless vacuum cleaner. My belt broke and someone else took it off. I bought a new belt but do not know where it goes on the cleaner. Please help


Easy to do. Unplug the vac. Turn the vacuum over and look for three finger latches on the bottom behind the brushes. Unlatch these and pull the faceplate off. Then, grab one side of the brush and pull straight up (they just sit in grooves on the ... Bissell CleanView 3596 Bagless Upright Vacuum

In trying to repair foot pedal on my Hoover Windtunnel self propelled bagged vacuum, I got carried away and took apart most of the unit and I am still not able to get to the release..... I need help fixing the release lever AND then advise as to how to put the sweeper back together....Help!


This video should help you ... Hoover Vacuums

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no


... Vacuums

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to


... Hoover U5344-900 WidePath Vacuum

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN


First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

I'm trying to replace the belt that drives the sprayer on my Bissell ProHeat but the package with the belts did not come with instructions. I keep finding instructions on the internet, but without pictures, I have no idea what I'm supposed to do. Please help.


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Eureka Altima vacuum. The model number is 2996. I don't think my vacumm is sucking any dust. Plus, it smells like a burning leather. What should I do? I have tried to get help from others and they tell me that I should change the belt. But, I don't know where it is. Please help.


Sounds like the belt for sure. Here is a link with the owners manual. It shows how to get to and change the belt. http://www.eureka.com/index.php?option=com_productdisplay&view=productdisplay&task=getproducts&productid=2&produ ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I just bought a new belt, put it on, took two swipes, smelled burnt rubber again. My new belt broke. Why?


The beater bar is probably not turning. It get's jammed up with hair and strings and Christmas icicles and anything else on the floor. Taking the bar out and cutting all the stuff off is the easiest way to clear it. Make sure it turns freely before y ... Eureka 2961AVZ Bagless Upright Vacuum

I am trying to find out a part number for a rubber gasket that goes on the inside of a Hoover Windtunnel Cyclonic Platinum BAgless upright. It is a very thin, light-weight gasket made of rubber that helps seal the filtering tubes. If you know where I can find a parts break down, please advise,,, JON [email protected]


Hi There,\015\012\015\012I'm not sure exactly which part you are asking about, so I went ahead and uploaded the parts schematic of your vacuum cleaner, that will diagram all the parts, and part numbers.\015\012\015\012If you n ... Hoover UH70015 Bagless Upright Cyclonic Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

Took apart the turbo head on my russell hobbs pet cyclonic 2000 to unblock it and am now unsure how it goes back together. please help


... Vacuums

It is making a racket when i turn it on. I took the brush off and cleaned it it is not the belt i don't know how to take the cover off the top front so i can look near the motor can you help please. [email protected] .com Thank you Staci Bishop


These units have two screws that hold the "hood" in place. With the belt/brush roll cover off look on the underside for the heads of these screws. Once these are removed the top should come off. ... Hoover U5096-930 Bagged Upright Vacuum

I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur


That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum

Makes a loud noise like a grinding noise then smokes comes out and it smells like burning rubber? When I take the (rod) brush off with the belt then run the vacuum there is no more noise? Please help me thank you


Your belt is worn and stretched and so it is slipping on the motor drive shaft. That is why it is noisy and smells like burning rubber. You simply need to replace the belt. You can get replacement belts here: ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1004 seconds