Having problems with your Kirby Generation 3 Bagged Upright Vacuum ?

Power problem I have a Generation III and lately the power button doesn't always work when it is pressed. You have to click it a couple of times and then it will turn on and sometimes it will even stop while I'm in the middle of using it. Thanks for your help

Answers :

I would replace the power switch. Here are the instructions for the repair...
Repair Help & Product Troubleshooting for Kirby Generation 3 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Power problem I have a Generation III and lately the power button doesn't always work when it is pressed. You have to click it a couple of times and then it will turn on and sometimes it will even stop while I'm in the middle of using it. Thanks for your help

I would replace the power switch. Here are the instructions for the repair...\015\012http://rev ... Kirby Generation 3 Bagged Upright Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on

... Miele Blue Moon Bagged Canister Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Dyson 28-animal- Power brush stopped working and power light and carpet level buttons all are blinking. Per the instructions vacuum needs reset by turning it off for 30 seconds. However after doing so it does not reset and work. Help!

... Dyson DC28 Animal Bagless Upright Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,

... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt

Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help

Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!

There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I'm not getting a water/soap flow out of the steam cleaner when I turn it on. Even the power shot piece isn't squirting out. Can you help?

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Shop-Vac 5870400 was working just fine, and then one day while i vac the floor its just stop working, tried to turn on/off a few times, swicth to different outlet. i did even tried to open it, but found no burn or anything that suspicious. i never drop nor used outside, only inside the house for normal vacumm. please help. thanks.

Same thing just happened to mine. My solution is to get another one but a different brand. I think it should have lasted longer than four years of fairly light usage. From what I read, if it does as we both described, the motor is shot and not wor ... Shop Vac 587-04-00 Canister Wet/Dry Vacuum

Hi, A few days ago I bought a Philips hairdryer (HP4935/22) & have used it only twice. Somehow when I used it this morning some of my hair got caught in the filter at the back of the dryer & the motor slowed down & I think overheated & stopped. Normally the filters come off but I don't think this one does. I haven't turned it back on so as not to possibly damage it even more. I am quite upset as I really love this hairdryer. It's quiet, light, small, powerful & does the job brilliantly. I h

This is usually a safety feature so it doesnt burn itself. If there is a lot of hair in there try pulling it out, and if there is a little try with it too, if you can try get it out with something. If you think there isnt any in there anymore, try to ... Philips Vacuums

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Hi my hoover vacuum, stopped working,does not even turn on,I accidently went over a shoelace but stopped before the shoelace went in, ,,becuase of that the belt came off,and then i put belt back on, and now it wont even turn on

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david

Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.

The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A

This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

The Dyson Animal won't turn on or off. The red power button doesn't control the on/off for this machine any longer. Once plugged in, the vacuum will work and the power cord must be unplugged to turn it off. Any help would be appreciated.

The machine needs a new switch. The switch is stuck to the "on" position. ... Dyson DC05 Bagless Canister Cyclonic Vacuum

My bissell power trak just stopped working i turned it off and a few hours later i turned it on again and it will not work. I switched over to an outlet i know works and it still didn't work I checked the outlet after and there's still power there. Is there an internal fuse?

... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

When the power head is turned on it goes from green light to red light and stops. The belt is fine and there is no obstructions in the brush to stop it from turning.

This will happen only when the brush or motor does not turn the right speed \015\012make sure to pull the end caps off the brush and clean any hairs or fibers from it\015\012the motor you can try and turn it by hand with out the belt on a ... Fantom Vacums Lighting Canister Vacuum

My dyson turns on but when i push it to vacuum it makes this awful sound like something got sucked up and caught. i turn it off and turn it over and nothing is stuck. My husband even looked at it and he thinks it's the belt. The belt doesn't turn as loose. Please help.

If yours is one of the DC07 models that has a clutch (there's a knob you can turn, close to the front on the right side - right as you look from behind, that is). Sometimes this problem is cured by simply turning that knob from one extreme to the oth ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0900 seconds