Having problems with your Kirby generation 3 vacuum cleaner ?

How do i detach the top plastic piece from the bag on kirby generation 3

This bag does not detach like the videos on line show. It has little cloth eyelets at the top held by a metal piece

Answers :

Repair Help & Product Troubleshooting for Kirby generation 3 vacuum cleaner

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vaccum Bag How do I change the vaccum bag? I no longer have the booklet. I keep hearing about a zipper. I can't find a zipper. There is sliding piece of plastic at the top. My bag is full, and I need to change it...Help!


Slide the plastic piece off the cloth bag and open the top. Looking down into the cloth bag, you will see the old bag. It is secured to the machine near the top. You will find the cardboard collar about a third of the way down. Remove it carefull. No ... Hoover Soft Light U4266-940 Bagged Upright Vacuum

My Kirby bag is filthy as the internal bag broke. How can I take th bottom plastic piece off to wash the bag??? Please can anyone help!!! Thank You


Madam try to shake the bag to remove the dirt if you cant remove the bag. or use a strong electric fan and let it blow the dirt. hope that helps\015\012\015\012\015\012CHARCOIS ... Kirby G5 Bagged Upright Vacuum

How do I detach the bag? - Kirby Generation 3 Bagged Upright Vacuum


Watch the instructional video on our site;\015\012http://www.goodvac.com/\015\012\015\012\015\012Good luck,\015\012Rocky ... Kirby Generation 3 Bagged Upright Vacuum

Kirby g4 vacuum- need to replace the plastic connection piece between the vacuum bag and the vacuum base...anyone know where and how to do this?


See if this helps\015\012http://www.goodvac.com/kb_results.asp?ID=12\015\012\015\012Good Luck,\015\012Rocky ... Kirby G4 Bagged Upright Vacuum

How do I detach the cloth bag from my Kirby G3 Vaccuum to wash it


I would clean the bag by blowing it out with compressed air (lightly). If you do wash it, do it by hand in room temp water and air dry. I'm not too sure how to remove the whole bag on that model. You should call your local vacuum dealer to inquire, ... Kirby Generation 3 Bagged Upright Vacuum

Have new oreck quest canister and having trouble figuring out how to change vacuum bag. I have the plastic piece that you attach bag to, but don't know where the piece fits into the vacuum. looking for a diagram or manual to see where to install the plastic piece


... Oreck Vacuums

Hi, I have a pre-lit christimas tree and the top section the plastic end that inserts into the previous section is broke. the company that provided the tree I guess is no longer in business. any idea how you would fix this? The top tilts because a piece of the plastic of is missing on the piece that inserts into the previous section..


Find a piece of metal pipe with an interior diameter the size of the stem. Cut it long enough to cover the plastic fitting completely and press it over the old one. Put the upper section in position and fill the missing part with shards of wood - ham ... Vacuums

How to remove the hinged plastic piece at the bottom of the bag?


... Oreck XL Ultra Bagged Upright Vacuum

I shipped my brother PE 770 embroidery machine purchased sept of 2010, to a lady who perchased it on ebay. Had used only once. Everything worked fine.I shipped in the original formed styrofoam box. I removed the embroidery arm, releasing the locking plastic hook holdind the machine and the arm together. When to lady removed the machine first in the original plastic shipping bag, two parts fell out. Her photo she emailed showed a black plastic piece with two holes or pivot points.also a silver me


This is a link to the manual for this machine. Do you see a picture in the manual of the parts you are describing? Reply with a part number and I will do my best to help. ... Vacuums

Kirby G 6 but it only blows air out, no suction. Also how do you detach the cloth bag to wash it?


I have the solution for the cloth bag laundering process...\015\012\015\012Here is a link to my guide for cleaning the Kirby cloth bag...\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

How much horsepower for a Kirby G3 - Kirby Generation 3 Bagged Upright Vacuum


All kirbys are good, i reccomend getting a G6 ... Kirby Generation 3 Bagged Upright Vacuum

I need a manual for a kirby vac gen #3 - Kirby Generation 3 Bagged Upright Vacuum


Click the link below for the manual It's a very large .pdf file, so just be patient while it loads;http://kirby.110mb.com/docs/kirby_sentria_manual.pdf ... Kirby Generation 3 Bagged Upright Vacuum

How to install Kirby g4 fan - Kirby Generation 3 Bagged Upright Vacuum


It needs to be stripped completly down, if you are confident at doing this then here goes.\015\012It has been a while for me so take your time and some of the steps may have to be completed slightly differently.\015\012Isolate / unplug t ... Kirby Generation 3 Bagged Upright Vacuum

Why does a kirby g3 goes on reverse only - Kirby Generation 3 Bagged Upright Vacuum


... Kirby Generation 3 Bagged Upright Vacuum

Kirby g3 upright will not pick up trash - Kirby Generation 3 Bagged Upright Vacuum


... Kirby Generation 3 Bagged Upright Vacuum

How to set up kirby to vacuum mattress - Kirby Generation 3 Bagged Upright Vacuum


Detach lower end of bag from body of vacuum.\015\012Attach hose to the opening.\015\012Attach above floor tool for vacuuming.\015\012\015\012See video instructions on below site.\015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum

Cant turn the bag connect to get it off - Kirby Generation 3 Bagged Upright Vacuum


... Kirby Generation 3 Bagged Upright Vacuum

My vacuum kirby turned by itself - Kirby Generation 3 Bagged Upright Vacuum


The problem was that the piece that you connect to the wall outlet was broken. I purchased a new cord and it is working fine now. Thank you! ... Kirby Generation 3 Bagged Upright Vacuum

How do I assemble kirby g3 carpet cleaner? - Kirby Generation 3 Bagged Upright Vacuum


Greetings,If you click the link below it will take you to a video demonstration that explains step by step what you need to do to convert your Kirby into a carpet shampooer. The vacuum in the video is the Kirby Sentria, but the procedure ... Kirby Generation 3 Bagged Upright Vacuum

Kirby g6- How do you replace the cord? - Kirby Generation 3 Bagged Upright Vacuum


I do believe o6 the cord goes in to the metal housing of the motor .They are usually held in by a rubber grommet and they can with some patience and force be pulled out slowly does it as you don't want the wires ... Kirby Generation 3 Bagged Upright Vacuum

My kirby will not turn on - Kirby Generation 3 Bagged Upright Vacuum


... Kirby Generation 3 Bagged Upright Vacuum

Dirt devil ud20020 plastic piece at top of dirt cup broke off.whole dirt cup canister will not fasten to vacumn.


... Dirt Devil Vacuums

My Generation 3 Mini Em-Tor is broken. It looks like I can just replace it and that it is connected to the cloth bag by plastic clamp. Is it that simple and do I need a new clamp too?


Hi there SmartAlec from nelsonvacuums.com.au here. It really is that simple Your local kirby dealer should have one in stock and it really is a common item. They should fit ... Kirby Generation 3 Bagged Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Where do you connect the attachment hose? - Kirby Generation 3 Bagged Upright Vacuum


You have to remove the brushroll nozzle and your attachment hose goes in its place set it on the cross rail, rotate up and lock in place. ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0443 seconds