Having problems with your Kirby Heritage I and II, and Legend I and II 14 inch Replacement Rolle ?

The brush on my kirby won't turn

\015 Can't get the brush to turn\015

Answers :

It may have something caught in the roller mechanism if not the belt that drives the roller may have broken or slipped off. If the problem is neither of these then the motor that drives the belt to drive the roller may have failed, Please take to an authorized service centre and have it repaired or replaced if it does not cost more than a new vacuum if it is going to cost more than a new vacuum then discard that machine and purchase a new one. I hope this helps.
Repair Help & Product Troubleshooting for Kirby Heritage I and II, and Legend I and II 14 inch Replacement Rolle

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kirby G7D model ultimate g, the diamond edition. i took the brush part off , and used the attachments, i put the brush back on, and now it wont turn on.


Did you happen to hit the N/D switch by accident on the bottom. The switch has to be in D to run. ... Kirby G6 Bagged Upright Vacuum

Kirby g4 brush wont turn belt ok


Your belt has stretched or worn so the roller brush cannot turn against the resistance of the carpet. You need to replace your belt. You can get one here: ... Kirby Ultimate G Bagged Upright Vacuum

My kirby is shorting out when i plug it in and turn it on it wont turn on and then after a little bit it will turnon but twhen you move it it will turn back off.. and there were sparks from the cord.... i was wondering if i still have a warrant to get another one ive never had a problem with my kirby i love it but am dissapointed that i cant use it


... Kirby G5 Bagged Upright Vacuum

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition


Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

Should the roller brush on the kirby always be spinning?? just inherited a kirby 5, and the roller brush is not turning when the vacume is on. ??


Yes it should alway be spinning when you switch on the machine, if it's not spinning i would sujest the belt as come off or broke this video will show and explane what you need to do to replace or put back on . ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Brush wont turn on my dyson....only had for 4 months....what do I do with this piece of crap?!?!


... Dyson DC39 Animal Canister Vacuum

My dyson dc25 just turned off while i was using it first the roller brush stoped turning so i used the hose and now it turned off and wont turn on how do i fix it?


... Dyson DC25 All Floors Bagless Upright Vacuum

Brushes wont turn on shampooer


Dear Momneville\015\012I have the same steamcleaner and had the same problem, I took mine apart a found a clog between the turbine and the wheel that the turbine moves by vacuum when it gets glogged there is no vacuum to move the wheel. If you ... Hoover F7220900 SteamVac V2 Upright Vacuum

The brush wont turn


Make sure that the carpet selector is on carpet setting not bare floor. It only spins on carpet setting. If carpet setting is engaged and still doesn't work you need a new clutch assembly. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

DC 17 UPRIGHT BRUSH MOTOR WONT STAY RUNNING. TURN


Have a look at the filters first as it sounds like you blokeage ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brushes still wont turn


I had same problem and it was the turbine assembly. Part was only $28 but with labor it cost me $140 total. Plus it took over 5 weeks for my vacuum repair shop to get the part. In hindsight, I would have just spent another $100-$150 dollars and bo ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

The brushes wont turn,but it has good suction for the hose


If the belt seems to ok, you may need to order a replacement clutch assembly. These are not that expensive and can be ordered through dyson or possibly online. Switching from bare floor to carpet while the motor is running is really stressful on th ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brushes wont turn one of the gears is striped


What is the make and model # i can check to see if what you need is available and give you a price and model # ... Vacuums

Uh70086 brush wont turn smells burning


... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Brush / roller wont turn


Most likely the belt is broken. Bad news regarding all Dyson's. You can't replace just the belt your self. You have to purchase a new belt assembly which includes the gears. And it wont be cheap. I would call it a design flaw but i am sure that ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I got new belts but the brush wont turn


Make sure the vacuum is on the carpet setting..the brush won't turn on the hard floor setting.. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Agitator brushes wont turn even after cleaning


The brushes will not turn even wen the switch is turned on ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dyson brush wont turn


Hi There is a reset switch on your Dyson that needs to be pressed when something gets stuck in the brushes. The reset switch helps protect the motor that spins the brush from damaging if something gets stuck inside the brushes. There is a little ... Dyson DC25 All Floors Bagless Upright Vacuum

Bissell pro heat 2x healthy home brushes wont turn


Hey Brenda! Here's a link to troubleshooting steps for the brushes not turning.\015\012http://www.bissell.com/FAQDetail.aspx?id=1128&cid=ccsocial ... Vacuums

Hi my dyson dc07 animal has suction but the brush bar wont turn. If I turn it on there is a horrible noise. The belt is still fine


The belt is probably worn or stretched. When this happens the belt won't turn\015\012the roller brush when it is against the carpet. Here is a link for the\015\012manual and links for the belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Motor wont turn on.I checked the switch and I think it is working.motor turns on if a put direct power to it.'but it smokes at the brushes. can you help?


This sounds like either the belt isn`t on right or the brush is not slotted in the vacuum right remove the plastic or metal cover from the bottom and check by inspecting the belts ability to easly turn the brush rod check with your hands DO NOT turn ... Kirby G4 Bagged Upright Vacuum

Brush wont turn..Pressed reset still no turn - Vacuums


If the motor runs and the brush doesn't turn, the first and best suspect is the belt. ... Vacuums

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Spin brushes wont spin and the switch wont turn machine off. I have to unplug it. 


For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0774 seconds