Having problems with your Kirby Heritage II Vacuum ?

Foot pedal not working

\015 Foot pedal height adjuster slips to lowest setting.\015

Answers :

Sounda like the rachect teeth inside peddle r worn out probably need to take to shop for repair
Repair Help & Product Troubleshooting for Kirby Heritage II Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have White Speedylock Serger, model 1500 that will not work when I press the foot pedal. I thought it might be the pedal, so I ordered one on-line, but the new one does not make it work either. I have checked the needle and it is fine, not loose or broken. The presser foot is fine also.

If either of the foot pedals are for sale I am interested. [email protected] ... Vacuums

Foot pedal not working

Sounda like the rachect teeth inside peddle r worn out probably need to take to shop for repair ... Kirby Heritage II Vacuum

The on off foot pedal is not working.

... Kirby Ultimate G Bagged Upright Vacuum

Hi. I have a Hoover SM1901 "Pets" and the foot "switch on" pedal is now not working. Is this easy to fix/repair?

... Vacuums

Our Bissell ProHeat carpet cleaner is not working. The power is connected because the red heat lamp is on, however when you touch the foot pedal for the start of the rollers, the power is not connecting. Short somewhere??? How to locate the short? Please advise. Thank you.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My G6 kirby stopped working. i have checked the wire for fraying and continuity and found no problems. I have noticed that the foot pedal that turns the machine on doesn't seem to click when pushed on or off either. i have the motor exposed now to check if it is bad, but i am not sure how to pursue doing just that.

... Kirby G6 Bagged Upright Vacuum

I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!

... Sharp Twin Energy EC-TU2607 Vacuum

I have a singer 328 and the foot pedal has developed a problem the machine is running all on its own can I fix the problem with the foot pedal

... SewShop.com 328 Singer Instruction Manual .pdf format

I have many SEBO automatic X4 vacuums with broken foot pedals. I would like to buy 5 foot pedals that I believe the part number is 5059DG can you tell me where to get it

I guess that depends where you live... plenty of spares sources online (google sebo vacuum spares)... otherwise google sebo dealerships in your country/locality. ... Sebo X4 Bagged Upright Vacuum

Foot pedal came apart.Trying to reconnect.Might be missing a part.Need a drawing on assembly for foot pedal that operates the shifting from the hose to the floor vac

\012It took some searching but the site you need is called "dyson medic.com" This is the place that will have the repair manual you are looking for. You are not alone in the world of broken dyson's. ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.

It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Where to buy on line, plug in and foot pedal cord, plus a pressure foot, for a scholastic 6510

This link may help youhttp://www.singerco.com/accessories/instruction-manuals ... SewShop.com Singer Model 6510 Scholastic Instruction Manual

Kenmore 31913 Foot pedal release lever broken-need to replace

FixYa techs - thank you for your response but I solved the problems. It took me 2 hours of continual searching but I finally found the parts - listed under the tab sew machines of all things!? There is one pedal in stock and I called t ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Wispertone 116.29429990 I need help in getting the cover off. The foot retractor pedal for the power cord has screws under it and I am afraid of breaking the it. How do I access the screws under the pedal?

The pedal may be tough but the attached pushrod that disengages the power cord reel ratchet may not be, and is stressed by reddevil6's maneuver. I'd prefer to go after the tabs that retain the pedal's forward end. They are part of the rear cover and ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I have a Electrolux canister model L-E (circa 1986). Won't turn on. I think the foot switch is broken inside. Was working fine - turned it off then would not turn on BUT foot switch sounded different, kinda hollow sound. Perhaps I'm reaching but wortha a shot? Mary

I have one of these LE models also. Yes, the on/off button is broken. I have had to replace it twice on mine. My local vacuum repair shop suggested NOT to use your foot to operate this switch, but just press it on or off with your fingers. That will ... Electrolux UltraLux 2000 Bagged Canister Vacuum

My Hoover T5703 has suddenly stopped working. I was using it, moved it to another room, presssed the start with my foot - and nothing! I have checked that the fuse and electricity socket are both OK.I did knock it over a while ago and am wondering if I have broken a bit of plastic in the foot starter. It doesn't seem to 'click' as firmly as it did, but I cannot see how to take it off to check?

... Hoover Vacuums

I havethe first generation purple Dyson Animal model. The brush rotates fine, but doesn't make sufficient contact with the floor/carpet, therefore does not pick up most items on carpets (suction still works however). If I put my foot on it and push down a little, it works. However, since I'm not an accomplished acrobat, this is not easy to do. :-) Any suggestions on whether this is fixable? Or should I just save up to buy a new one?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?

Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter

There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

I took my Dyson DC 25 Animal apart to clean it, and now the red foot pedal won't lock the vacuum into the upright position anymore. The trouble is the spring pin for the pedal popped out and I can't figure out where it is supposed to go.

That spring thing goes where the pedal screws into the side. When 'facing' the dyson in the front, it's on the left side. The spring's circle part and short stem section goes into a divot area on the pedal. The other end is tensioned (braced) a ... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson will not stay up in a locked postion, red foot pedal looks like it is too far in the gray pedal

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Let's try this again. The main vacuum and hose works fine, the "foot" does not. When I turn it on, it shuts off automatically and the light comes on telling me to "check brushroll". I did this and removed all hair, strings, etc., Still won't work. Please respond. The last post took over 30 minutes with no response.

Sounds like you have hair or carpet buildup in the roller and it is not freely rotating and you are getting an error. If there is no buildup, then roller bearings may be frozen up, or the unit has a faulty capacitor and is not going to work due to el ... Vacuums

I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.

... Vacuums

The red foot pedal won't stay up in a locked position

... Dyson DC25 All Floors Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0394 seconds