Having problems with your Kirby Heritage II Vacuum ?

My kirby heritage is having suction probleme what can i do

Answers :

Make sure there is no clog in the machine.
Repair Help & Product Troubleshooting for Kirby Heritage II Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kirby heritage is having suction probleme what can i do

Make sure there is no clog in the machine. ... Kirby Heritage II Vacuum

Kirby g5 suction problem

If its not picking up as an upright but does with the hose, youve either not connected the belt or the belt is broken ... Kirby G5 Bagged Upright Vacuum

My kirby g5 is not picking up, there is no blockage, but suction has dropped significantly, what could be the problem?

Not to question your description of the problem, but are you sure the suction has dropped? Kirbys don't usually lose suction unless there is a mechanical or electrical problem. When you turn the machine on does it fill with air and expand? If so, th ... Kirby G5 Bagged Upright Vacuum

Kirby heritage II vacuumn doesn't pick up much. have taken it in for repair a couple of times at a substantial and after a about a year same problem again. Have checked connections, cleaned out. please advise. Thank you

How does the kirby heritage toe control work and where does the sping go. ... Kirby Vacuums

Suction problem my proheat wont suction water out of carpet,,, it made a mess of my carpets now, any one no how to fix the suction problem?

The valve on the bottom of the water bucket is not being pushed up enough to allow the vaccuum to go through. Perhaps a part is missing but I used a small ball bearing and a car vaccuum cap to build it up and now our works but it is still a piece of ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Kirby Sentria I bought my kirby sentria just before we were to move house and although I have the instructions somewhere, they will be boxed up and I so want to clean the carpets before I move. Problem is that I don't know whether the belt should be on or off when using the big silver front with the Kirby insignia on it. I know that the green light should come on when it is working properly and it does not, so I am doing something wrong. I can attach the attachments no problem but I want to use

If the green light is off, then its time to replace the band. This video shows you how. ... Kirby Ultimate G Bagged Upright Vacuum


Make sure the lever it the very back of the machine is in the on or drive position, make sure the height is up high enough ( the higher the better as long as it is still cleaning - lower is not better ) and change the belt even if it isn't broken the ... Kirby G6 Bagged Upright Vacuum

Carbon Brushes wearing out quickly on Kirby Heritage II

4 possible reasons.1 – one or both bearings are worn so armature (rotating part) wobbles as it is spinning and cause motor brushes to wear fast. Solution – change bearings too.2 – Whoever replaced brushes – did not ... Kirby Heritage II Vacuum

Kirby g4 problem

1. Take the brush roll and belt off the vacuum. Put the head back on the vac.\015\0122. Turn it on and see if the bag inflates with good power. Does it sound normal? This will tell you if the problem is with the motor. If you have a good inflat ... Vacuums

Kirby heritage 2 repair manual - Kirby Heritage II Vacuum

... Kirby Heritage II Vacuum

Suction problems I have cleaned all filters and still have suction problems, making odd noise when turned on.

One thing Dyson did recommend is to take an air compressor (or hair dryer) to the thingy in the collection reservoir. This seemed to help a little... ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???

Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum

Kirby heritage mark 2

I know this is forever away, but I wanted the answer to be completed.The black brush lead wire attaches to the foot switch. It probably got pulled out when the unit was disassembled. Look at the side of the switch and where the power cord c ... Kirby Ultimate G Bagged Upright Vacuum

The suction on the Kirby Ultimate g is very weak

You probably have a small leak somewhere. it doesn't take much to lose suction. make sure everything is sealed between the vac and bag and make sure there's not a small hole in the bag. the impeller should be alright unless, you've vacuumed up someth ... Kirby Ultimate G Bagged Upright Vacuum

How to change belt on kirby heritage 2? - Kirby Heritage II Vacuum

... Kirby Heritage II Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.

Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How to change belt on kirby heritage vacuum - Kirby Heritage II Vacuum

... Kirby Heritage II Vacuum

Low suction Replacing filters....need help replacing the belt - anyone know how? But before doing these things, have had a problem with suction....I'll let you know if the problem clears up.

Hi, You can take care of both things at once. Here's how:\015\012Unplug and flip your vacuum over, beater bar side up. Remove the cover base plate that surrounds your beater bar. It's held on with either clips or screws, and usually "hinges ... Eureka 2961AVZ Bagless Upright Vacuum

How to change the fan in kirby heritage 2 - Kirby Heritage II Vacuum

This site has a great tutorial on how to do it. I did it myself and it worked out great. Get the parts online or at your ... Kirby Heritage II Vacuum

Where can I find kirby heritage vacuum brush belt 301282 and the vacuum bags for a 1984 kirby heritage?

... Vacuums

Is the kirby heritage ii self propelled - Kirby Heritage II Vacuum

... Kirby Heritage II Vacuum

Kirby heritage 2 motor runs slow then speeds up with burning smell.

Replace your belt and clean your roller brush. ... Kirby Vacuums

No suction vacuum working fine and suddenly, no suction at all....what could be the problem? no suction through the machine from either the wand or the floor/brush side

Sucked up a sock?? No seriously.. it may be as simple as that or that an on board filter is clogged. Check your manual for all filters and Hepa/screens and others. Also, is the unit making any odd noises since the non -suction scenario? Whining or s ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks

This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Poor suction I have a hoover hush s5627 vacuum purchased about 4 years ago from Costco. It's suction power isn't so good anymore. I've checked all the lines & hoses and they're clear and I've changed the bag. I even disconnected the pipe from the vacuum unit and held my hand over the intake. While the machine roars like a jet engine the suction power just ain't like it used to be. What could possibly be the problem?

This vaccuum has a Fan Blade inside connected to the motor that spins to create the suction you feel. After a few years of use (and misuse) the blades on this (plastic) fan will be broken off, thus damaging the unit. These Fans are replaceable if yo ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0795 seconds