Having problems with your Kirby Heritage II Vacuum ?

How do you put on the attachment hose?

\015 How do you put on the attachment hose of a kirby legend heritage II?\015

Answers :

The Heritage II Legend...First you make sure that the machine is unplugged from any outlet,. Now, raise your height adjust to the highest level. Next you will need to turn your belt lifter on the front of the nozzel to the right as far as you can. Now flip the hinged light cover up, and turn the latch that holds down the head to the left. Your nozzle is now released. Now take the hose and roll it on to the bar from the front to the back, make sure it is aligned and then turn the latch to the right locking the hose, and you are ready to kirby it up! Hope this fixesya! Let me know, Thanks, Rene (the Vacuum Doctor)
Repair Help & Product Troubleshooting for Kirby Heritage II Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you put on the attachment hose?


The Heritage II Legend...First you make sure that the machine is unplugged from any outlet,. Now, raise your height adjust to the highest level. Next you will need to turn your belt lifter on the front of the nozzel to the right as far as you can. N ... Kirby Heritage II Vacuum

I have taken this stupid vacuum into the repair and he said I have the belt put on incorrectly. I have watched the video many times and I am putting the stupid thing back together correctly and it will not ****. It does **** with just the hose attachment.


Sounds like a blockage in the base ... Kirby G5 Bagged Upright Vacuum

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o


It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum

My new Kenmoore Powermate 116 canister has poor suction. I have no pets and light dust. Its not picking up small particles on the wood floor with the floor attachment. When I put my hand to the suction it feels weak. Cleared hose and changed bag. Using again, same issues. This should not be happening with a new vacuum. Is it a bad design in the elbow joint of the hose? I want to return this!!!!


First of all disassemble the handle and hose as much as possible and examine the inside. Make sure there is not any significant debris lodged in the hose somewhere like a plastic bag or something.\015\012\015\012Also check at the top of t ... Kenmore 23912 Progressive PowerMate Bagged Canister Vacuum

I have the upright kenmore progressive with direct drive and the filter canister stops bringing in air and picking up when hose is put into vaccum, when you remove hose and use as an attachment it starts again


Check the hose after the brushes. With this problem there is normally a clog in between where you disconnect the hose (to use attachment) and the brushes that clean the carpet. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My dyson dc17 animal will pick up via the hose attachment but there is no suction when you use the regular vaccuum on the floor - you can hear the difference in the suction once you put the floor part down - we took it apart - cleaned it - checked all hoses - still does not work????


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I can't turn the belt off of my Kirby vacuum. I had the front off of it earlier to attach the hose, but now when I put the front back on, I can't get the belt to turn off. The lever twists about 3/4 of the way around, but will not go the rest of the way.


Turn the front part to the green so it is level and then twist the front to the red make sure the belt catch the hook as you twist it then if the belt is hooked just put it back on the vac like normal and lock it in place then twist it back to the gr ... Kirby Ultimate G Bagged Upright Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

I took the trap(or whatever it's called)off the bottom right corner to check for an obstruction as my hose was collapsing when using the attachments. Put it back on(perhaps wrong)and now when the vacuum is turned on, dust blows out the front and there is NO suction! HELP!


Now you have a dyson leaf blower! not funny huh? Ok, just slow down and recheck your connections. Sounds like the motor is running backwards or you are hook up to the discharge. ck for baffles that block off the vacuum to the roller part when at ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My handle won't go back up after an extended vacuuming session during which I used the hand/broom/animal hair attachments several times, thus pulling the hose out/putting it back in, starting/ stopping, and suddenly no matter what I do short of forcing it (and even if I try forcing it a bit) I can't raise the handle to put it away.


Do you know what model number Dyson you have? Is it the ball style one? Just find a similar product here on this page and let me know what model number is closest: ... Dyson Vacuums

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a bagless cyclonic shark stick vac. I cannot figure out where to put the hose to use the attachments.


... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

How to put the hose on to use the attachments on a Kirby


I will make a slide show with pictures to help fix your kirby. ... Kirby Ultimate G Bagged Upright Vacuum

Kirby shampooer The suds are not coming out of the shampooer. I made sure it was connected right. The sponge filter and the cap are attached. i have a g4 vacuum and the screen in in properly.. if i move at a snails pace i can get spots of suds about every 6 inches or so but not a lot. i have adjusted the on and off, if verified the video its put together correctly but it acts like no suction .. i thought of a small hole in the hose for the suds and cut off about 1 inch it act better but not by


On the shampooer tank, remove the screen cap from the little hole that the shampooer hose plugs onto. Clean the screen and make sure that it is not plugged up with debris. Make sure that the screen is securely glued to the cap all the way around the ... Kirby G4 Bagged Upright Vacuum

My Bissell Proheat Turbo puts out too much water and cleaner and won't **** it back up like it should. Also when I use the attachments dirty water runs out the the hose when I am done. It's used a lot, I shampoo all the carpets about 2 times a month and I shampoo the funiture 1 time a month. I bought it about 3 months ago.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How do you put on the attachment hose to clean sta...


Assuming the rug nozzle is currently attached, lift up the headlight hood. Twist the belt lifter (black plastic square) on the rug nozzle counterclockwise to remove the belt tension. Then pull the accessory lock up until the rug nozzle comes loose ... Kirby Heritage II Vacuum

Dyson Animal hose collapses when using attachment hose


You have a clog in either your hose or your wand. You need to take off the wand and hose and inspect them. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

When hose is attached vacuum stops


There is a clog somewhere in your hose, wand or head\015\012a plummer snake will get it or even a broom handle ... Electrolux Lux 7000 Bagged Canister Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have no suction on a DC25 attachement hose only. I feel no air being suctioned out of this attachment hose..


... Dyson DC25 All Floors Bagless Upright Vacuum

Bissell Pro Heat 7901 will spay through hose but not the floor and red flow indicator will not spin. So we took the housing off and after unclogging a hose running to the hearter, my husband unhooked the hose that goes to the flow indicator, blew in it and it started spinning. Put the deep cleaner back together, tried to use it and nothing. What else can we try? Can't afford to put it in the shop right now. Thanks in advance.


I borrowed my friends bissell to clean my carpet. It's the 7901. He brought it over and told me that it only sprayed out of the attachment hose. He said he couldn't figure out what was wrong. I'm no vacuum technician but, I am a mechnic. I decided to ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

Hose attachment On my dyson dc 25 the hose attachment is very hard to pull off. It seems like something is getting hung up when i try to pull up the hose.


Your wand is getting stuck in the hose because the hose is twisted - you need to unwind it:\015\012\015\0121) Pull the wand up as far as you can, all the way if possible\015\0122) Stretch the hose out and unwind it, use some babypow ... Dyson DC25 All Floors Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0565 seconds