Having problems with your Kirby Heritage II Vacuum ?

Kirby Heritage 2 fan replacement

\015 How do I replace the fan assembly in my Kirby Heritage 2 vacuum?Also is there a site where I can download a repair manual?Carl\015

Answers :

Take the bag asm. and handle off. Then remove the plastic strip covering the switch, remove the screw there, remove the 3 screws on the housing, turn it over and loosen the screw near the back, the housing should come off. Then remove the screws on the back of the fan casing. You shouild be able to get to the fan, hold the fan and turn the spindle to the right to take off. If it would turn off, then you may have to lock the armature so it can't turn to move it. Then re-asemble in reverse.
I put a vise grip on the disintergrated fan to hold the armature whilst I spun the top locking spindle off, pretty easy stuff
Repair Help & Product Troubleshooting for Kirby Heritage II Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby Heritage 2 fan replacement


Take the bag asm. and handle off. Then remove the plastic strip covering the switch, remove the screw there, remove the 3 screws on the housing, turn it over and loosen the screw near the back, the housing should come off. Then remove the screws on ... Kirby Heritage II Vacuum

I need to replace the fan blades on a Kirby Heritage II, Model 2HD, vacuum cleaner. How do I remove the drive shaft that the fan is mounted on? Thanks, Robert Croft


... Vacuums

How do I get the case apart on my Kirby Heritage II (2HD) to replace the fan impeller? I can only find 3 screws holding it and there seems to be more.


From the rear, there are 3 screws on right and one on the lower left. There is 1 more on the front at the top just under the lamp. You will also need to remove the safety switch - the plastic thing down and just right of the front screw. Tak ... Kirby Heritage II Vacuum

Replacing the fan hub on a kirby classic omega 1CB


I resolved the problem .I found a way to hold the armature shaft still while I unscrewed the pulley drive nut ,which must be removed in order to remove the vacuum fan.\015\012\015\012> There probably is a special tool somewhere that w ... Kirby Heritage II Vacuum

Fan and bearing replacement on a Kirby G6


If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

How to change the fan in kirby heritage 2 - Kirby Heritage II Vacuum


This site has a great tutorial on how to do it. I did it myself and it worked out great. Get the parts online or at your ... Kirby Heritage II Vacuum

Kirby Heritage II Replacing the Motor in the housing HELP!


... Kirby Heritage II Vacuum

Broken fan need a repair man or service centre. If not a replacement fan for self repair. I live on the Gold Coast Ray is my name. Kirby Legend 1 model 2HE


Http://www.ultimatesanitarysupply.com/pdfs/VacuumMaintenance.pdf\015\012\015\012see the link ... Kirby Vacuums

Replace Kirby legend II fan (impeller blade) - Kirby G4 Bagged Upright Vacuum


In order to replace the fan you will buy a 2 or three piece lexan fan kit containing the fan a spacer and shaft. You must remove the carpet head and then looking from the back of the machine you will find a series of philips screws on the oute ... Kirby G4 Bagged Upright Vacuum

I have a Kirby Heritage II Turbo and I need a user's manual, but can't find one anywhere. I have to replace the fill tube in the bag and can see the cable tie on top that holds it in place, but don't know how it's attached to the mini-emtor. If I can't replace the fill tube, will tape fix it? If I just taped it; will it hold? Thanks.


Taping usually just causes a mess. The mini-emptor has coarse threads on it that the fill tube screws on to. Occasionally there is a cable tie on the bottom which is not really necessary. If you cut the tube near the bottom, you can get hold of it's ... Kirby Heritage II Vacuum

Kirby Heritage II 2HD Vaccum Cleaner. I have removed the housing and reached the motor shaft for the vacuum fan. How do you remove the fan from the shaft.


Hi, you can visit this site to view how to remove the fan from the shaft...http://www.diyonline.com/servlet/GIB_BaseT/diylib_article.html?session.docid=1678Take care ... Vacuums

Bad fan how to remove fan on kirby heritage 2 legend vacuum cleaner.


There might be latex sealant around the perimeter of the fan casing. This was the case with my G3. The latex sealant prevents dust from blowing out of the fan "chamber" while it's running and under positive pressure. And as reddevil16 said, the spind ... Kirby Ultimate G Bagged Upright Vacuum

Kirby G3 made loud noise when running. Sprayed silicon in fan thinking it might be a bearing. Found a coin and nail in fan and removed. Tha vacuum would not turn on. Replaced switch and brushes. Still nothing. Did the silicon spray do something?


No - the silicon is an insulating material and would have no effect on the electrics of the vacuum. Most likely you have a bad connection - dismantle the vacuum again and check the wiring and the motor with an ohmmeter. Be very attentive with the bru ... Kirby Generation 3 Bagged Upright Vacuum

Kirby Lexan Fan is crack and need help to replace


Hello...\015\012Check out my online instructions...\015\012\015\012http://reviews.ebay. ... Kirby G4 Bagged Upright Vacuum

I need to replace the fan and am not sure Kirby G 4 A


Greetings from GoVacuum,\015\012\015\012We've shot a video showing you detailed instructions on how to replace the fan on a Kirby Generation vacuum cleaner. The video is in two parts below. If this video was helpful to you, please be s ... Kirby G4 Bagged Upright Vacuum

I replaced the impeller fan on my Kirby Classic III, it all went back together fine, but there was a leftover piece- the commutator brush cap. Where does it go? Oh, the vac isn't powering up eit


... Vacuums

Replacing the bearing behind fan on a kirby heiritage II 2hd


I don't know what model of Kirby you have but on all Kirby's that I know of you have to remove the fan. Here are two vid's on fan removal for a generation series vacuum. ... Vacuums

Broken Lexan fan needs to be replaced


It is similar to the G4 but without the tech drive so is easier. ... Kirby Heritage II Vacuum

I,m down to the removal of the bust fan on my kirby heritage but how do i do this stage


Ok so Once i took off the back/engine cover (lift the plastic near the switch theres another screww there) go the front and take out the 2 screwws that hold the hose attachment switch.I you hold the fan and insert a strong bar/small screwwdri ... Kirby Heritage II Vacuum

Replace carpet cleaner belt - Kirby Heritage II Vacuum


... Kirby Heritage II Vacuum

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.


The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

No manual, want to replace fan Impeller - Kirby G4 Bagged Upright Vacuum


Hi,\015\012 Here is their instructional video....click below\015\012http://www.kirby.com/Portals/0/videos.html\015\012\015\012 He ... Kirby G4 Bagged Upright Vacuum

Trying to replace fan on Kirby g5 but the whole thing keeps turning and I can't get it off, any suggestions?


The threads are left handed on the shaft. opposite than what everyone is used to. there are flat spots on the back of the motor armature where you can put a wrench to hold it from spinning. ... Kirby G5 Bagged Upright Vacuum

Replace fan impeller on Kirby Legend II - Vacuums


Take to repair shop u have have the tools needed to replace ... Vacuums

Replacing fan assembly on Kirby G2000 - Vacuums


This video should get you half way there:\015\012Kirby belt replacement\015\012\015\012Hope it helps ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0431 seconds