Having problems with your Kirby Heritage II Vacuum ?
How do you remove the brush from the rug rennovator?
See utube for video showing you how
Repair Help & Product Troubleshooting for Kirby Heritage II Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How do you remove the brush from the rug rennovator?
See utube for video showing you how ... Kirby Heritage II Vacuum
I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes
Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??
... Kirby Vacuums
While using my Dyson a rug got caught and that ratcheting sound started. I removed all signs of strings, etc until the brushes rotated fine but when I started the Dyson the ratcheting started again. I have the DC 14 Animal.
The rattly sound means the drive belt has snapped or the protective clutch has slipped. This needs repair by someone who knows how to repair Dysons officially. Sadly its the kind of model that can't be done by the owner. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Is it possible to remove the brush bar from the housing of a mieleTurbobrush STB 205? The brush bar is not spinning due to been dirty and clogged and needs to be removed for cleaning. Is it possible to remove the brush bar????
... Miele 06271980 STB 205-3 Turbobrush
Just purchased this Dyson dc24 today. brush doesn't spin after gettin tangled in a cord. removed the cord from the brush OK. I have several times: removed the brush and replaced it OK. pushed the red button by the brush. pressed the brush power switch.
When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not roun ... Dyson Ball DC24 Bagless Upright Vacuum
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help
Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum
Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!
Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum
I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.
Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.
Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums
Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help
The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
How to clean sebo rug brush
There's a button lock on the top of the nozzle and the bottom of the vacuum where they meet. That should release the carpet nozzle from the vacuum cleaner easily.. you may have to jiggle it to get it loose, but there's a button lock mechanism that ho ... Sebo 9803AM Upright Vacuum
My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab
(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum
Electrolux power nozzle, model 1692, power cuts on and off. I don't have the manual for it, but I'm trying to remove and clean the brush compartment. I removed the top, but not sure how to get to the brush. I would like to find a manual for it, because it's completely different than the one I use to have.
... Electrolux Vacuums
My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.
Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum
My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?
... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
String caught in end of rug brush
This pdf file should help you - there are instructions in it for removal of the roller.\015\012\015\012http://www.managemyhome.com/mmh/lis ... Kenmore 25512/ 25513 Progressive Canister Vacuum
How to clean the power brush on the miele vacuum. Is the brush removable? If so how do you remove it?
Greetings from GoVacuum.com,Miele canisters have 2 different types of power brushes. The first, and most popular is the Miele SEB 217, and 213 Power heads. To remove the brush, follow these instructions.On the bottom of the ... Miele Vacuums
I have a Hoover V2 Windtunnel and the brushes are not turning. I have removed the black plate, removed the 4 brushes, now what?
Check for hair / fibre lodged in machine and brushes, remove it then re-assemble ... Hoover F7220900 SteamVac V2 Upright Vacuum
I removed the revolving brush to remove a jammed piece of debris I had picked up and after putting brush back, it no longer revolves
Reattach your belt properly and the beater will function.\015\012\015\012Thanks for your interest in FixYa.com ... Vacuums
My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.
Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum
I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i
Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums
Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help
Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums
Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)
I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum