Having problems with your Kirby Heritage II Vacuum ?

How do you replace the front roller bearing?

\015 Bearing is trapped by impeller on one side and motor cooling fan on other - how do you get the impeller off?\015

Answers :

Repair Help & Product Troubleshooting for Kirby Heritage II Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you replace the front roller bearing?


... Kirby Heritage II Vacuum

Replacement front and rear bearings on main shaft


Usually you replace the rear bearing and the complete front bearing cover assy. the rear bearing will have to be pressed off and the new one pressed in, let me know how deep you are into the project so i know where to start. ... Kirby G5 Bagged Upright Vacuum

I have Eureka model 2961. The bearings on the end of the roller have seized and melted the plastic end. I was wondering if you know where I can find replacement bearings and a new plastic end cap.


Here are a couple of links:\015\012\015\012http://www.vacpartswarehouse.com/Products-p/62228-3.htm\015\012\015\012 ... Eureka 2961AVZ Bagless Upright Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

How do you replace the bearings on the roller brush?


... Bissell Cleanview Helix Deluxe Bagless Upright Vacuum Cleaner 21K3

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

I need a "Bearing Assembly" for roller brush 61445-1,I Have a GE 106575


Probably should just go to a repair shop and they should be able to order one for you, that is if they are available by themselfs. Or if you have a store where you live that sells vacuum parts, you could go there. ... GE 106585 Upright Vacuum

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

How do you reattach the front rollers on hoover elite rewind so that the carpet height adjustment works


... Hoover Vacuums

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.


... Sebo X4 Bagged Upright Vacuum

I have a hayward 1HP superpump with an Ao Smith UST 1102 motor on it. Last year I had a leak in the pump, and I believe I got some water in the bearings of the motor. Over the winter I replaced all the seals in the pump, and have no leaks this year, but the pump is sounding pretty loud since opening the pool this year. I have (2) fold question: (1)I can not find any information on the where I can find a replacement bearing for this pump. (2) I can not find a procedure on HOW to go about


Hello. I get my parts here http://www.poolcenter.com/parts_pumps_hayward_superpump.htm\015\012\015\012Joe ... Vacuums

The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not


... Riccar 8850 Vacuum

I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers


The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums

I have a GE 106766 Canister Vacuum. The belt on the power end stretched and I replaced it. Now the roller froze up and won't move. Where can I find a replacement roller?


Try this sitehttp://www.onlinevacuumparts.com/ps-328-7-ge-6850-106766-canister-power-nozzle-parts.aspx ... GE 106766 Bagged Canister Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dyson DC07 brush roller is worn and won't make contact with the carpet anymore. I need to replace the brush roller but don't know how...HELP?


Buy the brush over the web etc..\015\012\015\012To take the brush out \015\0121 - Take the outer covering - uese a penny to turn the yellow srews\015\012\015\0122 - Slide the black brush out from the assembly - Try the n ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Fan and bearing replacement on a Kirby G6


If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef


Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

My vacume is less than 6 months old. I've gone through & replaced 4 belts. Now I realize the roller is not rolling which is causing the belts to break. The roller is free of all hair and debree. What should I do to fit the roller?


Very strong chance the end caps, made out of rubber could be a manufacturer defect. Many parts on vacs are made by different sources. ... Bissell Vacuums

Roller I recently removed my roller to cut all the hair off it and when I replaced it everything snapped right in but when I turned the power on the power worked but the roller wouldn't turn


Hi.\015\012\015\012Did you put the drive belt back on the roller ? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

How to refit the front brush belt driven roller ? We removed the roller accidentaly when cleaning out hair that had got wrapped around the roller. How can we put it back in?


Hi well if you go onto youtube and look for replace dyson clutch it will show you how to refit your brush good luck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Replacing Front Wheel Assembly


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0360 seconds