Having problems with your Kirby Sentria ?
Shampooer leaves very thin stripe even when going slow
Head is all the way down but barely leaves any shampoo on carpet.
Repair Help & Product Troubleshooting for Kirby Sentria
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h
Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums
Shampooer instructions..... I have a Kirby Generation 3 with the shampooer. it has been awhile since i have used it and i sort of remember how to attach it but i was wondering this vacuum has a tray and i assume it is for sucking up the dirty water but when i went to use it no dirty water was going into the tray.....help what did i do wrong......thank you for your time...............spanny
Try this link....http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTI ... Kirby Generation 3 Bagged Upright Vacuum
Bissell carpet shampooer, how do I use it there was no manualI just need bASIC INSTRUCTIONS I'm guessing push button to release shampoo, go over the whole area, scrub as necessary, then it will **** up drity water. Question there is a rinse button Does that mean that I have to go over it again 3x?
Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.
... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
My irobot starts out running fine and then it will turn and slow down as if something is keeping it from going. all at once it will go full speed again. it does this until finally it stops and the red status light comes on. I just replaced the battery 6 months ago.
... iRobot 4296 Robotic Vacuum
I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m
... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara
I have a 5260D Baby Lock Serger, which I had tuned up a year ago. I haven't used it very much since. When I took it in, and again now, it sews fine for awhile, then starts slowing down until it is barely sewing, even with the foot all the way down. The hand wheel seems very tight. - it doesn't turn freely, but takes a some push, like it is resisting a bit. Any idea what could cause this slow down and the tight hand wheel? I appreciate any ideas. Thank you. Maura
Hi,Since you say that you didn't use it for many years then does it make noise?If so it need oiling on its parts.oil orifice and point of contact.Please do rate the solution if the issue is resolved or post a comme ... Vacuums
Where can I get a replacement glass lid for Rival crock pot model #3100/2? The one listed below is out of stock, but, even if it were, it will not fit my model. Any suggestions? "Buy-it-now-store.com" lists: CURRENTLY OUT OF STOCK, NO ETA. # Rival Crock Pot Lid Replacement Glass for 3.5 Quart Rival Slow Cookers - $5.99 Rival Crock Pot Slow Cooker Replacement Round Glass Lid Cover # Works with Rival Crock Pot Models: 3100, 3101, 3102, 3103, 3130, 3133, 3120, 3250 # Approximate total
Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o
It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum
While vacuuming, it leaves a stripe of dirt. It has suction but leaves a strip of material on carpet
Check the brush and make sure all threads, hair, and similar materials are cleared. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
What parts go to a Kirby Shampooer?
There is a shampooer head with shampooer brushroll, water tank, small hose that hooks to the tank, collection trayNeed to use the Kirby shampoo. It goes down as wet suds but you pick up the suds with the vacuum when it drys. Fill tank add ... Kirby G5 Bagged Upright Vacuum
Shampooer leaves spots
If the spots are NOT at the center of the unit - you may have washed the brush roll. Older style shampooer brush rolls could retain a lot of water and it is all dirty in there. NEVER wash the brush. Just after you are done - raise the nozzle and let ... Kirby Ultimate G Bagged Upright Vacuum
Dirty Water drops behind shampooer
You are over sudsing your recovery tank. The machine is made to shut off the air flow if water starts to be pulled into the motor, but bubbles want trigger that. So if there are a lot of bubbles in your recovery tank, the get sucked into ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Kirby shampooer is leaving streaks and shampoo comes out in a small streak
Go to this link for instruction on how to use shampooerhttp://www.goodvac.com/Articles.asp?ID=153 ... Kirby Vacuums
Shampooer won't distribute foam/soap evenly
Disconnect the hose from the tray - if you are getting good flow of the foam - I'd say you probably did not lower the shampooer all the way down.If the foam is not being dispensed continuously - you may want to check:1. Check the ... Kirby G4 Bagged Upright Vacuum
Rainbow shampooer The soap dispenser on my Rainbow is not dispensing soap when I flip the switch to 'soap' mode. All connections are intact. All plastic hoses are intact. What do you think is going on? The soap bottle connects to a little straw that appears to be free of obstruction, however, it connects into a sealed casing on the hose.
The little "wash/rinse" switch on some of the Aquamate units shuts off the soap flow by kinking the tube inside the housing. If you leave the switch in the rinse position (therefore, kinked) when you're done using it, it may dry in the kinked positi ... Rainbow E series Canister Wet/Dry Vacuum
No power going to hoover have hoover turbo power 3. Plug is sealed but have changed fuse. Have had builders in house using it to renovate bathroom. Do you think it is now passed its sell by date was working until they got it. It dosent even switch on. Am ready to do them an injury as my upstairs is a mess
A Neighbour fixed it ... Hoover Vacuums
Bag indicator light won't go off, therefore vaccuum cleaner won't run. It acts as if the bag is full even with a new bag.
The bag indicator is either rusted out or broken. it only realy's on a little spring that bounces up and down so dont trust those things ... Vacuums
Vacuum keeps going off even after reseting reset button
There's an obvious electrical problem. Examine the cord, especially near the plug. Check for kinks and blackened areas in it as well.\015\012There's a good possibility of an electrical short in the vacuum itself. \015\012I suggest takin ... Oreck XL Ultra Bagged Upright Vacuum
Rainbow Shampooer Where do the two tubes go at the bottom on the canister? Easy to hook up the hose but no place to hook up the tubes.
It's been while since I used one. Hopefully things haven't changed.\015\012\015\012One hose has to be be connected to the faucet of the sink using the adaptor. The other hose is supposed to go to the Rainbow iteslf.\015\012\ ... Rainbow E series Canister Wet/Dry Vacuum
High pitch My Hoover fusion vacuum cleaner began making a high pitch sound that makes it very annoying to vacuum. I cleaned all the things I could clean. I even cut out all the hair that was entangled in the brushes. Any idea what is causing the sound. It sounds like an siren is going off.
The Hoover Fusion has design flaws in the motor, including a metal plate that is too thin to contain the forces acting on the motor, particularly the constant strong tension from the drive belt, and a plastic plate that is attached to the metal plate ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum
My Dyson ball sucks fine while moving forward, when pulled backward it leaves hair or whatever on the floor. Works fine going forward????
The brushes will not spin anymore and the switch to go from spin to locked does nothing this is on a hoover steam vac shampooer
Pull out the brush block, make sure it will turn and to see if the shaft is on it, the shaft goes up into the turbine. If the block is ok, then the turbine isn't working. You take it apart and clean out the turbine, or replace it. ... Vacuums
D.d vaccum i have a dirt devil dynamite...i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!
Did you check the brush roll, if the ends aren't turning freely, then it needs to be replaced also. ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum