Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

I have aKirby Diamand series 4 years old

\015 Iturned my kirby vac off for a couple of minutes. I tried to start it but it wouldn't start. what could be wrong with it?\015

Answers :

Reason number 1 (not sure why Kirby Co. still has not fixed it) -improperly installed outer bag. You have to push the bag all the way tothe unit so it presses the safety switch that is between exhaust andthe vacuum shell

Reason 2 - defective cord - try wiggling it. Ifyou know how to do it - try removing cord and supplying power directlyto the unit using another cord or wire (ONLY if you know how to workwith electricity.If you get zapped - do not blame me)

Reason 3 - bad power switch (instructions on how to replace it HERE)

Reason 4 (very unlikely) - motor KAPUT

Good Luck
Rocky
:-)
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have aKirby Diamand series 4 years old


Reason number 1 (not sure why Kirby Co. still has not fixed it) -improperly installed outer bag. You have to push the bag all the way tothe unit so it presses the safety switch that is between exhaust andthe vacuum shellReason 2 - defecti ... Kirby Ultimate G Bagged Upright Vacuum

I purchased a used Minuteman 2400 series buffer/burnisher over the weekend from a store that is closing. The unit is about 7-8 years old. I did not get a manual with this item, can you help me out with this. I would like to read up on it so if I have problems I can look back on it. Even as far as the operation of it would help to have a book for it. Linda


I have this manual available via email. chris321 at gmail. ... Vacuums

I cannot get the sprays from either the bottom or the handpieces to work. I only get a short "gurgle" of fluid when I first press the controls. I have cleaned both the top and bottom cap and insert parts, and I have turned the machine off and on numerous times, have allowed it several minutes to warm up. But still no luck. Bissell Turbo 2X 9500 series (3 years old) D B Davis Camas,WA


It sounds like the pump has malfunctioned. I own a Bissell Big Green Clean Machine.You can actually order a 50 foot hose and run it from the sink to the hand piece or the part that is supposed to spray to the floor. This hose can handle ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a swivel sweeper, the original series, that is about one year old and is losing power. The battery has been replaced but it still seems weaker than it used to be. The brushes do not turn as quickly and the overall pick-up is not as strong as it was when it was new. Any suggestions on how to get the power back up to what it once was?


HiThank you for your queryI think what you will find is the base of the sweeper has 4 brushes, each of these brushes are run from a cog, if you can take the base apart you will find that it has been clogged up with hair and ot ... As Seen On TV Swivel Sweeper Vacuum

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Bissel spot bot water not coming out of tank is not a year old and tried manual wand and the water doesn't come out there either. any advice. Is not a year old yet.


You could take the end of the handle off 2 screws i think check the line for a clog or just take it to a bissell service center it will be covered under warranty ... Bissell SpotBot Robotic Wet/Dry Vacuum

The motor just went out on my 2 year old vacuum with light usage (hardwood floors in a very small house.) The Sears repairpeople are estimating ~ $130 to fix (this includes parts & labor). I'm wondering if it's worth investing $130 into something i've spent $350 on only 2 years ago. Shouldn't these machines last longer ? Is there something I could do to get them repair free as it seems the motor must have been faulty to only have lasted 2 years. Thoughts ?


Aye, get a dyson, if its out of warranty there's not much u can do bout it :( ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dyson animal We bought a Dyson Animal from Sears a few years ago along with a service contract. We took it each year to be serviced. One year I took it because it lost it's suction. They sent it to the factory, but it came back still not working right. We did the same procedure over ands over many times than I can remember. I now have the cleaner in my garage and am using my old vacuum because I just can't seem to get anywhere with Sears. Please help me. We paid almost $600.00 and now it can't b


As someone who works for Sears, let me just say right now.. The service contract you bought sucks.. and does not really do anything for you. it was just a wast of money ( they have a new one now.. thats so much better because you get your money back ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t


... Vacuums

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt


You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.


Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust contai ... Vacuums

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.


Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Very little suction on my dyson dc24 yellow ball upright . only 21/2 years old.. should i take it to a vacumn repair shop ? it has a 5 year repair guarantee. I cannot find the papers. But i know that i filled out the guarantee & miled it in. what should i do?????


I'd look at this:\015\012\015\012http://www.fixya.com/support/t2827418-very_little_suction_in_hose_no_tears_in ... Dyson Ball DC24 Bagless Upright Vacuum

Need a replacement on/off switch for Dirt Devil Deluxe Model 8201 (more than 12 years old). We have the old one out. We just need a new one to replace it. Where can we get one?


... Dirt Devil Vacuums

I recently took out a stand mixer that is probably over 50 years old. It belonged to my mother and I wanted to use it. It probably hasn't been used in at least 10 years. With some effort, I removed one of the beaters but cannot remove the other one nor can I even budge it. I have used WD-40 but it's not helping. It's a Westinghouse product. Any ideas? Thanks.


If you used WD40, you should have the unit inverted so the WD40 runs down into the beater socket.Use a small piece of wood and place it against the bottom of the beater and tap lightly with a hammer while pressing the beater release button/lever, jus ... Vacuums

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

I'm not really a technician, but I used to sell Filter Queens and was taught how to maintain them, and have tackled "fixing" some problems. I am a 71 year old great-grandmother of 8, but have good health and am very active. The Filter Queen I have is r, usedeally old, and I have kept it up. Just this week, however, I turned it on and it had a noise which sounds like something might be loose in the motor. I have always been very careful to have a clean hepa filter to protect the motor, so I know


It's tricky to hold screws with one hand and screwdriver with other hand; however, I am 65-yr-old female and do it yearly with 100% perfection! Take a break, relax, and try again! I sit on floor, put attachment between legs for supporting vacuum, h ... Filter Queen Majestic Canister Vacuum

Bought an PlayStation 2 at our youngest dauthers 9 year birthday together with an dance mat. Caused by an accident we had to buy a new remote contol for some years ago and we chosed your URC-3445. We can't get it to work. How do we get to AV-chanel throughtout your device? There must be a solution at our problem. Please help ....! Her anniversery is unfortunally today!!! Our TV is an rater old Tandberg modell: TVF2915NT Please...


Go to menu settings, find channel edit or add/delete, turn channel to input or a/v channel, select add channel and then your good. You should now be able to use the ps2. You can also hook them up through vcr and use the vcr input/av channel. and then ... Vacuums

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums

I have a Bissell PowerSteamer, Clearview approximately six years old. My son borrowed it two years ago and lost the instructions. I can't find a model number on it and need the instruction book. Thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.


I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hello, My Electrolux Renaissance is about 12 years old. It worked great for years, but now it keeps turning itself off...about every 15 seconds or so. The bag was just changed recently, too. Is there an easy, (and cheap) fix or should I start shopping for a new one?? Thanks!


Odds are you have an obstruction somewhere. Check all of the hoses and the power head to ensure that there is nothing blocking your airflow. \015\012\015\012Also note that if it keeps popping the front bag door open, that's usually indica ... Electrolux Vacuums

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

DYSON DC17 ABOUT 4 YEARS OLD. I HAVE TWO FILTERS THAT I ALTERNATE BECAUSE AFTER 2 HOURS OF VACUUMING I LOSE SUCTION. I HAVE TO WAIT 3 DAYS FOR MY FILTER TO DRY BEFORE I CAN SWITCH THEM AGAIN. THE FIRST TWO YEARS I HAD THE DYSON I COULD GO A COUPLE MONTHS BEFORE CHANGING THE FILTER. WHATS WRONG?


Hi there! This is John from Jerry's Vacuum Sales in Modesto Ca. Are you using any type of carpet fresh product on your carpet? If so the fine powder is leaking onto the filters and causing them to clog. Discontinue use and over time the problem will ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0382 seconds