Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

The outblow is OK but the suction is very low in both positions

\015 It does not pick up small growels like sand. I can not find anything that blocks the suktion\015

Answers :

Try changing the belt or changing the bag
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The outblow is OK but the suction is very low in both positions


Try changing the belt or changing the bag ... Kirby Ultimate G Bagged Upright Vacuum

When using my vacum upright its very low in suction, it used to be so powerfull that it lifted my carpet slightly....when using the tools section its as strong as it should be please help, ive cleaned it out but still loss of suction in upright position, from mrs richmond


Check the following items:\015\012\015\012* The bag and connection - change it if it's full\015\012\015\012* Turn the vacuum over and inspect the beater bar area for any clogging. You may have to remove the bottom plate to ... Vacuums

Dyson 14 suction low when using footplate


Hello,There could be a few things that would cause your Dyson to have no suction. I will give you detailed step by step instructions along with pictures on how you can diagnose this.Possible Problem #1. The first problem is extreme ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis


U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Oreck trouble I replaced the plug and switch. black from motor to pole 1, black from plug to pole 2, white tied to white with a wire nut. When I plug it in it is powered in the off position. I have high speed at the high speed position, low speed at the low and off positions. Any ideas?


... Oreck XL Ultra Bagged Upright Vacuum

Low suction The beater bar still spins fine, but the suction seems low. I have cleaned all of the filters, but it is still too low to spin a lot of the attachments.


Hi Megan,I'm sorry to hear you're having difficulties with your DC17. If it doesn't seem to be picking up as well as usual, you may have a blockage somewhere in the machine. To check for this, please follow the steps shown in our online suppo ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Low suction My old rainbow seized up. I purchased another one on e-bay. It works but it has a broken latch on the side and it has low suction. Even when I press down so it is sealed to the water can it doesn't inprove the suction.


\015\012\015\012\015\012With years of use, you will collect a layer of "micro dust" on the impeller (the fan part) which reduces the efficiency. A toothbrush and some mild cleaner with gently scrubbing will restore it's power. \015\012 ... Rainbow E series Canister Wet/Dry Vacuum

Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative


Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums

Low suction I have an Electrolux central vac that is approx. 11 yrs old. the suction is very low. this started about 1 week ago. I checked the hose and it is clear. I also went into the attic and checked the pipes(as far as I could see them) and they appeared to be intact.


1) Have you checked the filter? If it is clogged your suction will be low. Also, you could have a pipe loose where you can't see. Make sure that you can get a coin to go all the way through the hose. make sure the suction motor ( the unit ) is coming ... Electrolux Central Vacuum

Low suction My 2001 machine is has low suction. The motor sounds fine what could this be?


Is the suction low at the tank after you disconnect the hose? If it is strong there, then the hose may be clogged. You can unhook the hose from the wands to see if you have suction or not. If you do, then look further down all the way to the brush ... Rainbow E series Canister Wet/Dry Vacuum

I have a Dyson DC24/ all floors, serial number 530-US-D78353 that I have registered already w/ your company. The vacuum is generating suction from the main outlet (that goes to the canister)///but once I place the canister into position..there is no suction from the floor foot. The roller is working/spinning, but no suction..picks up nothing, I have cleaned and rechecked all filters and can not figure out why I suddenly have no suction. Appreciate your input and/or advise where there is a local


... Dyson Ball DC24 Bagless Upright Vacuum

Vacuum won't **** in upright position, but there is suction from the hose in the upright position


Theres a knob that switches it from floors to carpet turn the to floors.please leave feedback ... Vacuums

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s


I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

Hi...there is no suction in my upright's hose...there is suction when regular carpet cleaning but when I put it in an upright position and take the hose out there is extemely light suction.


... Miele S7210 Bagged Upright Vacuum

Low suction on Nilfisk King


... Nilfisk Family Vac Bagged Canister Vacuum

My electrolux oxygen cannister has the "bag change" light on when there is a new bag. The light stays on when the suction power is high (to pick up small particles) and it won't pick up, but the ight goes off when the suction power is low (to pick up big objects). I changed the hepa filter, cleaned the motor filter and changed bags, but all that didn't help.


You may have a clog in the hose, and/or the inlet by the brush roll. A clog will turn on that light as well as a full bag. ... Vacuums

Suction perfect when in upright position, but when tilted to actually clean there is total loss of suction - cannot see blockage anywhere. Thanks for your help.


If you are confident there are no blockages, look underneath, where the brush is, and you will see a short length of reinforced clear plastic hose. This often develops a split which results in loss of suction. You can pull the hose off at the motor e ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When I engage the vacuum cleaner by going from the upright position to the slanted position there is loss of suction.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have full suction with the hose and when the brush is off of the vacuum. However, in the vacuuming position, there isn't enough suction to pick anything up. I checked for clogs and cleaned all the filters.


So I have exactly the opposite problem, it sucks in floor mode but the hand held has zero suction. My daughter and i just spent the last hour disassembling and diagnosing and found this: The way the suction tube is configured, you have two places to ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The suction only works when upright, when in the recline position there is no suction and it starts to smoke


You probably have suction just no aggitation. those units use a clutch assy with two belts unfortunately when the belts fail you have to replace the whole assy just like everything else on the dysons. check your brushroll for rotation and for hair wr ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Rainbow d3c beaterbar has low suction Vacuum itself has great suction


Did you check the hose or the power nozzle it might have holes in it. ... 3M SV-497AJM Vacuum

DC07 hose has plenty of suction. Main hosuing has no suction. Beater bar turns fine and works so well creates positive air pressure blowing outward instead of vacuum. Any ideas?


Main housing has no suction becouse of bloakage in it. UPLUG the unit from mains, and remove the bottom (main housing)cover. Clean all you can access and put everything back together. In all the vacuum cleaners all the problems is caused usuall ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0472 seconds