Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

I put in a ne Kirby Bag and it still is not sucking up the dirt. The brush is turning but the bag does not seem to be getting any sucking snce it is not expanding

Answers :

See if this helps:
\015\012Good Luck,
You can remove the outer and inner bags and remote the hose that the dirt discharges and drop a screw driver or anything small and heavy enough and drop it in there. When you hear it hit something and it doesn't come out the other end, put your hands on each end of the hose and shake it. The clog should then be dislodged and come out the other end. Since that's done, put the vacuum bag back together and wash your hands with disinfectant soap thoroughly with warm water and see if these steps solved your problem. Good luck!
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I put in a ne Kirby Bag and it still is not sucking up the dirt. The brush is turning but the bag does not seem to be getting any sucking snce it is not expanding

See if this helps:\015\012http://www.goodvac.com/kb_results.asp?ID=13\015\012\015\012Good Luck,\015\012Rocky ... Kirby Ultimate G Bagged Upright Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Not sucking i have a KIRBY G3 that was working great. One day there was a strong smell and the brush roller belt broke so I replaced it. The fan looks good. Now the vacuum does not **** up dirt but instead seems to very gently blow air forward. I took the (new) bag off and it is blowing hard int the bag. I am stumped!

Belt is not connect to the drive pulley, see manual for fitting or see utube for video ... Kirby Generation 3 Bagged Upright Vacuum

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem

... Oreck XL2200 Bagged Upright Vacuum

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


My Hoover Mach 5 model number u5194-900 series ZF12.O will vacuum for about 15-10 min then it shuts its self off and will not turn back on., I have cleaned out all the hoses, filters and cleaned off brush. What can I do to fix this so that it will **** into the chamber. The hoses get clogged and it doesn't appear to be sucking into the "bag area"

... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

The brush spins but the the dirt is not getting into the bag. i cleaned the hoses now it's not sucking anything up.

If the motor is running you should get some kind of sucktion, if no sucktion or wont blow any air out, check the house making sure is clear of any obtruction, the best way is looking in the house by have one person hold one end and other pull the hou ... Vacuums

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab

(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!

First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

Helping out someone that has a ECV 1590A model 117A Electrolux central Vacuum. There seems to be a problem with the brushes. I'm looking for a manual or what brushes to get or a new motor. It seems to run fine what it starts.

... Electrolux Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th

... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you

Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.

First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

My FEIN 9-55-'13 recently started making more noise and is now officially a "screamer". There also developed quite a vibration associated with the noise which made me think it was probably bearings. So I took it apart and found no detectable play or lateral movement in the bearings, they seem fine to me. So I thought perhaps the brushes. The rotor where the brushes ride is quite black but I can't figure out how to get to those brushes, although I don't really think they are causing the noise

This problem is only caused by one thing the motor bearings are noisy, I have never found any other reason, they may look good and fell good but trust me replace the motor and the noise ... Fein 9-55-13 Turbo II Bagged Canister Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Hi, I have a Dirt Devil Model # M08100REDC. I desperately need to change the bag, but I don't see an obvious way to do it. I'm afraid to try pulling on the cloth tab thingy that's just below the handle, between the rubber ring that holds the bag on the vac, because it seems like stuff will fly everywhere from the force required to remove it, and I might not be able to get it back on there. Should I just pull on that cloth tab until the bag comes off? Thanks, Roberta

You can pull on the tab to remove the bag, but probably a better way is to gently pull on the rubber ring that attaches the bag to the back of the vacuum body. If you don't yank and ****, it should come off without spilling the dirt. There may also b ... Dirt Devil Classic M08100 Bagged Handheld Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

My dyson DC23 sucked up some plastic bags in the hose. How do I get them out?

... Dyson DC23 Bagless Canister Cyclonic Vacuum

Brush is spinnning and put in new bag but we get

Your Vacuum might have a hair ball. ... Hoover U5491-900 Bagged Upright Vacuum

Brushes at bottom of vacuum are not sucking up anything. It seems like its blowing out instead of sucking on the bottom.

Blockage somewear ... Dirt Devil Vacuums

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?

As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Hoover 6446 900 WindTunnel Bagged Upright has little suction at the floor brush but plenty at hose if disconnected. It does not seem that there is anything blocking the inlet at the floor brush.

Check for a clog in the brush hose ... Hoover Tempo Widepath Upright Vacuum - Blue
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2044 seconds