Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?
Not coming on
\015 When I attach the brush head, the vacuum will not come on, but when I attach the hose it will. is the switch in the front defective?\015
Yes, if the little "nipple" on the power head that plugs into the switch hole isn't broken off, than you probably need a new switch. I have written a repair guide to do this repair yourself. The folks who have used it have found it to be very helpful. Just click on the link to view the guide...
Kirby switches are complicated and expensive. Replacing one is very involved and requires that the machine be almost totally dissmantled. It sounds like the agitator housing is not going on far enough to press the part of the switch that governs that function. Take the housing off again and re-install it and turn on the machine. If it still doen't run, grab the housing but the sides, (careful of the roller if it starts) and wiggle it or rock it. This will usually trigger the switch to come on. If not, you will probably have to refer the repair to a competent repair shop. This repair can cost almost $100.00. The switch itself can cost $60.00.
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
We have the water hooked up at the back of machine. there is a spout for the water to come in and fill the ice tray.but is does not. If we turn the water on it fills up the space under the ice basket. I keep getting red light and then the two smal llight one ice and one water come on. We can hear the motor trying to fill the ice try and then lights come on. Please help me this so I can use this product. It did not come with a manual.
The water inlet valve on the back of unit opens when the ice maker needs water. If the valve doesn't seal good because of sediment or wear it will continue to drip and when the water reaches the ice maker supply tube it will freeze blocking the fill ... Vacuums
I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks
... Bissell 3750 Lift Off Bagless Upright Vacuum
Have DC07 that won't come on. Wife said this started happening a few weeks ago. Would come on and then other times would not come on. Now will not come on at all. Believe I have a lose wire. Have taken off star screw by on off switch, but cannot find how to get plastic parts apart to get into electrical connections. How do I do this? I am sure I am missing something simple?
... Dyson DC07 Bagless Upright Cyclonic Vacuum
My problem is that dust is shooting out of my powerforce bagless bissell. I pulled and detached the filters, hitting them againt my front steps which is cement, burshing my hand across the filter . Yes there was dust coming from it there. I continued to do this until no more dust is coming from it. When I cut it back on I'm still seeing dust depris coming from the vac.
... Bissell 6594 PowerForce Bagless Upright Vacuum
I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi
Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums
Electrical problem The light comes on but the motor will not come on when the on button is pressed. Is there a reset button? I thought it was because the bag was full but I just changed the bag and the motor still will not come on.
The light is separate from motor. No reset switch. Check for a fuse but i suspect it may be brushes are worn out and not making contact.Sometimes that starts as an intermittent.Hopefully one of the coils isn't open circuited. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum
The automatic drain hose is hooked up to the back of the unit, but when the bucket is full, the automatic pump does not work. The automatic pump should come on and empty the bucket, but it does not come on unless the water is siphoned manually through the tube. Then the pump come on and empties the bucket. I have reattached the tube and still had to manually siphon the water through the tube. Any suggestions?
Any automatic pumps operate off a swith that is turned on when the water rises. They normally have some type of ball lift, that will raise the switch when water is high and then drops with the water and shuts the pumps off. It sounds like yours is ... Vacuums
I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.
... Broan-NuTone VX475 Bagged Central System Vacuum
Over heating Light Comes on as soon as I try to turn the unit on. I have a Miele S558 Silver Moon vacuum that has only been used once and it shut off and will not come back on. The overheating light comes on as soon as I try to switch speeds on the handle or turn the unit on at the canister, and the vacuum will not run. Do you have any idea what the problem is?
... Miele s558 Silver Moon Vacuum
No steam come out.The base of the machine is hot how ever no steam come out
... Euro-Pro Shark Steam Blaster Vacuum
Steam not coming out of the bottom of shark vacuum its coming out of the top
... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Charge light on roomba won't come on when charging. Light on charger is on and shows unit is docked, but no light comes on roomba red unit itself. Is this a bad battery or problem with unit itself??
... iRobot Roomba Red 4100 Bagless Robotic Vacuum
Steam doesn't come out anymore when I pull the trigger. I think the water in the tank is getting hot, but when I pull the trigger, only a little water comes out. No steam
Try putting some white vinegar in the tank to dissolve any hard water deposits. You should use only distilled water in this machine. Don't try to clean anything with the vinegar in it, but take it outside to run the vinegar through. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Hoover wiring the blue wire that is in the lead that runs from the hoover to the plug that goes in the wall has come loose at the hoover end and has come out of the actual hoover. i've unscrewed it but am unsure as to where the blue lead (bare copper) needs to be screwed... if you see what i mean?!!
Hello lukeplayer,\015\012Based on your description, ( first disconnect the plug from the wall recptacle).You will need to open up the Hoover Vacuum Body to gaion access to the internal wiring. In order to better assist you, please provide me wi ... Hoover Vacuums
Bissell 2x has suction coming out of the "base" part(when I put my had over the rubber ring that leads from base to the handle part there's suction), but there's no suction coming out of the hose. I'm not certain if there's a clog, 'cause I can't get the hose off.
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Water will not come out when i push on trigger button. So water does not come out. I have taken it apart and cleaned it. The problem seems to be in the triggerI push on the handle to release the water.
Order the part from bissel see if that fixes sound like you know what wrong just need get part number from bissell.Could be some kinda pump also thats bad not pushing out the water.I got bissle heated one black it only problem the seals r ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u
Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums
Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth
Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum
No mixture coming in contact with carpet from machine but coming when tools are used
Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Is this free? i have a bissell carpet cleaner and i cannot get the soap and water to come out. it will **** up the dirty water however. i just found the belt is broken but i can see no way of how to put a new one in. is a broken belt the reason no soap is coming out?
If it is the flat belt that broke, that is the pump belt, the pump can't work without it. To replace the belts, turn the unit over, remove the red holder, has one screw, pull it out, then the brush roll will come loose. You can replace the belts th ... Bissell Powersteamer 1694 Upright Vacuum
We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't
If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums
I have a Rainbow E2 series, 23, for about 3 years. It has now a different and very aloud sound coming fron around the motor and also I feel it is not suctioning with the same power. If I close the hose like closing totally the suction entrance, the sound comes normally. I will appreciate if some one can tell me what to do, becouse there is not a Dealer in my Contry any more. Thank You. Pierre Chabaneix - Lima-Peru [email protected]
Hi there, Pierre!\015\012Sorry, but I think this is bad news. From your description, I suspect that a motor bearing has failed. The only way to fix it is to replace the motor, and without a dealer in your country, that could be a big problem.\015\012 ... Rainbow E series Canister Wet/Dry Vacuum
DIRTY WATER THE FRESH WATER AND SOLUTION COMES OUTON TO THE CARPET, BUT NO DIRTY WATER IS COMING INTO THE CANISTER.
Remove the dirty water tank and see if the front nozzle is fitted correctly, also see if the filter is clean on the dirty water tank ... Bissell 1770 Quicksteamer II Upright Vacuum
I just replaced the belt on my Kirby Heritage II, and it keeps coming off. It is engaged when I check it, but as soon as I start vacuuming, it comes off?!
You got the wrong size. ... Kirby Heritage II Vacuum
I have a hoover steamvac dual v and is leaking, bristels not working very food only two are speaning and is not sucking any water Very little solution comes out, or comes out in streaks when pressing the solution dispenser button on the handle. I think the lines may be stopped upped.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=41020&thid=634728\015\012I have a Hoover SteamVac\015\012Posted by albazo on May 30, 2008\015\012I have a Hoover ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum