Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

Shampooer the small ring screen that makes the subs basically wont stay in place. no matter what i try it keeps popping off


Answers :

Hi,
\015\012I suggest regular scotch tape or masking tape. Just take the screen out and cut a piece of tape into strips that are just wide enough to fit the outside of the screen ring without any excess. Put the tape strip(s) around the outside of the ring. This will make it a bit thicker/tighter and it will stay up inside it's hole. If the screen gets a buildup of residue on it, it won't make bubbles, so it does need to be cleaned on occasion and can be removed again easily when using this method.
\015\012Marci
If it is falling off (and lodging itself into the hose) I would suggest gluing it in place on the tank...a super glue should keep it in place and there is no reason to remove it. If its glued to the tank there is less chance of it being damaged.
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shampooer the small ring screen that makes the subs basically wont stay in place. no matter what i try it keeps popping off


Hi,\015\012I suggest regular scotch tape or masking tape. Just take the screen out and cut a piece of tape into strips that are just wide enough to fit the outside of the screen ring without any excess. Put the tape strip(s) around the outside ... Kirby Ultimate G Bagged Upright Vacuum

My Eureka/The Boss doesn't seem to have the suction power it had. However, when I place my hand under the hose, it has good suction, then when I try to pull in a small particle, it doesn't, unless I have the hose nozzle completely over the particle. The vac is 10 yrs. old. I cleaned everything. Someone said the belt. Would the belt matter if the hose doesn't **** well? It is just old and worn out? It did shut off recently do to overheating. Help. Thanks. Lorraine


Doesn't "The Boss" Vacuum have a filter? Perhaps your filter is clogged and not allowing it to work properly. ... Vacuums

Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee


... Vacuums

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.


... Panasonic Kenmore Canister Vacuum Vacuum

Filter inside the ball keeps popping out of place


Hi Katie, I'm sorry to hear you're having difficulty with your DC25's filter. If it doesn't seem to stay in place during use, I'd encourage you to get in touch with us directly as we should be able to resolve this for you.You can reac ... Dyson DC25 Animal Bagless Upright Vacuum

HEPA post-filter on Dyson DC25 doesn't stay secure causing the ball not to roll smoothly. the red button keeps popping causing the filter to pop up enough to cause the ball not to spin freely.


... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

I have a proheat carpet cleaner model 3 7901. the problem is the brush on the bottom of the machine plus the two end parts and the belt came out. i put everything back but they popped out, they are not staying in place. what am i doing wrong or what do i have to take out to get everything in place correctly?


Hi\015\012\015\0121. You’ll need to follow this procedure to assemble your unit back together.\015\0122. Make sure the foot pedal is in the proper position.\015\0123. The SmartMix should be properly loaded into the main ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!


Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks


This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

MODEL F7226-900 ON THE SMALL TANK THAT THE CLEANING SOLUTION IS IN THE SPRING WILL NOT STAY IN PLACE WITH THE OTHER PEACE WHAT DO IDO BILL . THANK-YOU


... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

My FIL purchased an Electrolux bagless canister vacuum model EL5 76501 last year. When I tried to use it today, the hose keeps pulling out of the power brush whenever I pull it towards me. it doesn't seem like anything has broken off. The only thing I noticed was that the rubber ring washer seems to be flattened. Could it be something that simple or do you think some part has fallen off and gone missing? Regards, Craig Somersett


I believe I've just had the same problem and after searching for a small gray horsehoe clip that needs to first be found and then inserted into the slot for it on the tube section that comes out of the beater bar. Insert this clip from the outside af ... Electrolux Vacuums

DZ9080 IRON IS NOT VERY OLD, BUT HAS HEATING AND STEAMING PROBLEMS. IT MAY BE ALL HEATING RELATED! MY WIFE WILL SOMETIMES JUST LEAVE IT "ON" FOR TWO HOURS AND THEN IT WILL START STEAMING AGAIN. I CANNOT MAKE SENSE OF THE HEATING INDICATORS; SOMETIMES IT WILL STAY GREEN NO MATTER WHERE YOU SET THE DIAL ---- AND IT DOES NOT FEEL HOT! WHEN I TRIED IT AGAIN TODAY, THE SHOT-OF-STEAM WORKED FOR A WHILE (AND THE SPRAY WORKED), BUT THEN ALL IT WOULD DO IS DRIP WATER AT THE TIP WHEN TIPPED DOWNWARD.


I couldn't find any warranty information on this iron, but I suspect that the heating element either has a faulty connection or part of it has cracked, making contact at time, but poor contact at other times. The unit will have to be taken apart an ... Rowenta Vacuums

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f


Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

Detergent bottle keeps falling off, wont stay put and clean water isn't emptying at all


The tank assembly needs to be replaced. Keep your tank handle. The other problem is your water not dispensing. There are electric solenoids and a pump that control dispensing soap and water. Take it to a repair shop for complete diagnosis before you ... Hoover Vacuums

The hollow tube underneath my dyson dc04 keeps coming out of position and it wont pick up. Should it be fastened into place with something.


It is suppose to swivel some. That is why it is not fastened in with a screw. It sounds like to plastic molding that was suppose to hold it in place has worn down. You will need to replaced that part. ... Dyson Vacuums

Im trying to replace the belt in my widepath tempo. Once I put it in the roller.... I don't see what it should attach to, to work and stay in place. ?? Please guide me.


... Hoover Vacuums

Roomba 560, the small red light above the schedule button will not reset and the roomba will not run. The problem started when I the roomba sat dead for 12 hours. I tried the spot dock reset trick with no luck. The clock and sunday light stay let also.


This work ok for me ihave a 560 thanks ... iRobot Roomba 560 Robotic Vacuum

Dyson dc14 animal is falling apart! The canister keeps falling our and now the carpet/floor adjuster doesn't work AND the brush wont turn....tried everything. I live in Half Moon Bay, CA (near San Francisco) where can I bring it to be OVERHAULED? Thanks


The best sol would be to search for vacuum repair half moon bay, ca. To see if there is a vac shop near you. my suggestion's would be either Vacuum Cleaner Shop #(877) 822-8227 or Vacuum solotions #(502) 348-4900. hope this helps ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have Bissell 8910 Proheat. The clear view window (half moon shaped) fell off & broke. I tried to place it back under but it would not stay. It is now not sucking up water. how come? I also am having a hard time finding a part to buy for it.


... Bissell 8910 ProHeat Clear View Upright Vacuum

My Scooba floor cleaner "check tank" light stays on even after it's refilled and everything cleaned but still will not work. It just keeps beeping at me when I try to start it. How do I reset it or get the light to turn off so I can wash my floors?


Flush out the solution valve with water (aka "prime the pump"). Use water, not just air, because water will clear any obstructions that may be in the lines. Also, rinse your tank through the four ports on the *underside*-- one round, two oval, one la ... iRobot 5800 Scooba Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0509 seconds