Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

When I replace the rubber on the cylinder and return the lever handle to it's original position in order to close it, the rubber comes off. How may I resolve this frustrating problem? thanks, bw


Answers :

See if the clip that holds the belt is not bent make sure the belt is hooking on and getting hooked on to the engine shaft.
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I replace the rubber on the cylinder and return the lever handle to it's original position in order to close it, the rubber comes off. How may I resolve this frustrating problem? thanks, bw


See if the clip that holds the belt is not bent make sure the belt is hooking on and getting hooked on to the engine shaft. ... Kirby Ultimate G Bagged Upright Vacuum

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.


It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The rubber seal strip inside of the vacuum system on top and on the bottom has started coming off. I was wondering if I could reorder this rubber seal stripping to replace on my system. The model number on my system is #91740. MV 261414/1 is another number that was labeled on the back of machine as well. We ordered it off of QVC and the name of this vacuum system is called, Cook's Essentials's Vacuum Packaging System. Thank you for you time. Look forward to hearing back from you soon.


... Vacuums

I have a Z345 Electrolux cylinder vacuum cleaner, from the 1970s probably, but not used much. I have lost the guide. I forgot to change the bag before it was full. Smoke started to come out - smelling of burnt paper, not rubber. So switched off. It did not blow the fuse, and may be OK. I wish to inspect it. How do I open it up? Alos I have an air filter and a motor filter for it. I have often changed the air filter on the top. How do I get at the motor filter, if there is one? Than


Good day! OK you have to is replaced the bag and that's it.And don't forget to change the bag again to avoid that problem.Thank you ... Electrolux Guardian Bagged Canister Vacuum

There is a rubber valve on the top of Dyson DC14 all floors. When the vacum is locked in its upright position or the hand wand is used there is a whistling sound coming out of the valve. When the vac is used as a floor vac, it does not make the sound. Is this something that I can fix? Is there an obstruction somewhere that would be causing this sound? thank you.


The Fixya user in this repair is giving out personal contact information rather then helping the customer out on the Fixya board. This defeats the whole purpose of Fixya if the "TheDysonTeam" just gives out his phone number and helps the customer o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The small screw-in plug (below 2-in-1 water tank) was removed in error, and the small plunger, rubber stopper, metal ring and spring came out. In wat order are they to be re-set within the such that fluid can be released correctly instead of all fluids coming out at once?


The metal ring goes first then the spring "Sits" on that washer, the plunger goes into the spring, then the rubber stopper goes on the end. OK. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a 41a5021-18 chamberlain security+ 1/2 hp garage opener that requires constant pressure on the down position of the wall switch in order to close. If I release the switch the door reverses direction and completely opens.


... Vacuums

My garage door opener will start to close then stop and go back to the open position. If I put pressure on the door as it is closing sometimes it will close all the way and sometimes it will return to the open position. Can you help me. Thanks


Sounds like the pressure sensor is being tripped - this is a safety feature on most makes in the last 10 years.Find the make/model of your device and it probably has some knobs on the main unit to adjust. For example, on the ... Vacuums

The pile adjustment wheel on my Sebo X4 has come off; I ordered a new wheel thinking that it would come with the PIN/AXLE but it doesnt. What do I need to order noe? I cant seem to find the pin as a spare part. Dp I need to order a servo motor? Many thanks Hannah


... Sebo X4 Bagged Upright Vacuum

I have a Rainbow E2 series, 23, for about 3 years. It has now a different and very aloud sound coming fron around the motor and also I feel it is not suctioning with the same power. If I close the hose like closing totally the suction entrance, the sound comes normally. I will appreciate if some one can tell me what to do, becouse there is not a Dealer in my Contry any more. Thank You. Pierre Chabaneix - Lima-Peru [email protected]


Hi there, Pierre!\015\012Sorry, but I think this is bad news. From your description, I suspect that a motor bearing has failed. The only way to fix it is to replace the motor, and without a dealer in your country, that could be a big problem.\015\012 ... Rainbow E series Canister Wet/Dry Vacuum

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?


... Dyson DC25 Animal Bagless Upright Vacuum

I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!


There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum

I fill the SE3306C steamer 50 ml, close the safety cap put it on and the light becomes green but no steam will come out ! Is it because I don't close the safety cap right ??


... Vacuums

Bissell 2x has suction coming out of the "base" part(when I put my had over the rubber ring that leads from base to the handle part there's suction), but there's no suction coming out of the hose. I'm not certain if there's a clog, 'cause I can't get the hose off.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?


This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums

I have a 5 yr old Ariens snowblower ( model # 924124). I am having a problem with the deflector cable freezing. I had the deflector cable replaced a yr or 2 ago. I took the cable off and brought it in the house to thaw. When I reinstalled the cable, it worked ine except the shute does not operate in its full range of motion. I have the cable EXACTLY in its original position and routing. The shute only closes about half way. I cannot get the shute to close any lower. Any suggestions?


... Vacuums

Small rubber cap that fits on nipple at bottom of solution tank came off, spring and check ball fell out. What's the order of reassembly? Also, can I glue the rubber cap to the nipple to prevent this in the future?


May I get the model # to help you more ... Bissell 1720-1 Little Green Wet/Dry Vacuum

I have a hoover steamvac dual v and is leaking, bristels not working very food only two are speaning and is not sucking any water Very little solution comes out, or comes out in streaks when pressing the solution dispenser button on the handle. I think the lines may be stopped upped.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=41020&thid=634728\015\012I have a Hoover SteamVac\015\012Posted by albazo on May 30, 2008\015\012I have a Hoover ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

I have a new Kenmore magic bued and I am about to change bags for the first time. Trying to do this the clip that is supposed to hod the bag close to the whole keeps coming off when I replace it and close the lid, turn on the vac the sucction is very low and it keeps showing the bag is full which is not true / what is going wrong here ? Thanks so much for supporting, Beba


Sorry to hear that you are having problems with you Kenmore Magic Blue.There is a so-called "bag full indicator", which will only turn red if it got some major blockage. This is the reason why there is no power suction.The "fu ... Kenmore Magic Blue 24195 Bagged Canister Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

My Dyson upright suddenly won't stay in the upright position. It appears that a little rubber piece has fallen out of position.


- Stand behind the vacuum cleaner and look at the right-hand side wheel\015\012- Remove the AI PIPE (it has two purple buttons that you push together to lift it up and out - it looks like a Tuba)\015\012- Lay the handle down and look for ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I shut my vacume off to change its bag out. Now it won't come on. Oreck xl2. There were no noises before turning it off or any smells of rubber burning. Just won't come back on. Is there a reset button. What can I do?


An access panel mounted atop a vacuum nozzle base via finger operated latches. When the latches are undone the access panel is removed from the top surface of the nozzle base allowing access to the parts of the brush assembly. The panel also has a ... Oreck XL Ultra Bagged Upright Vacuum

I have a Hoover Anniversary Special Edition and the Power Brush stays in the Off position. What am I doing wrong. It will not go into the "on" position. I have changed the floor surfaces and still it does not come on?


Hi,Have you checked the Brush On/Off switch?If you find that switch is not working :-Order it at :-http://www.govacuum.com/hoovwinonswi.htmlAlso, Try to adjust the position of the brush. Som ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.


This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum

The brush on my Kenmore Pet Power Mate no longer spins. I opened it up and found the problem may be with the rubber band connecting the spinning parts. Where might I purchase a new rubber band for it?


Try this link > http://www.vacuums24x7.com/kenmoreparts.html ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0598 seconds