Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?
Broken transmission belt
\015 My G5 has a broken belt inside the transmission and I can see the factory # still on it. PD 554289 , the local shops say they have never taken apart a tranny and that I need to buy a new transmission . this just does not sound right . there must be a way to buy a new belt again , I hope. thank you for any help .\015
Hi There,\015\012 Is it the main drive belts from the motor to the tech drive?\015\012\015\012If it is the are very easy to replace by taking out the tech drive.\015\012\015\012If it's a belt inside the tech drive unit you will not be able to buy the belts anyway as they are classed from kirby as a sealed unit.\015\012\015\012Hope this helps\015\012\015\012Chris\015\012\015\012www.elidistribution.co.uk
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Broken transmission belt
Hi There,\015\012 Is it the main drive belts from the motor to the tech drive?\015\012\015\012If it is the are very easy to replace by taking out the tech drive.\015\012\015\012If it's a belt inside the tech drive unit you will not be able to ... Kirby Ultimate G Bagged Upright Vacuum
The belt is broken on our Hoover Allergen Filtration Model U5018-900 120 v. 60 Hz 12.0 A. Belt 38528040. Where can I get the belt and instructions on how to replace the broken belt?
The owner's manual can be downloaded here (in red, "Download the Instruction Manual (PDF))\015\012http://www.hoover.com/product.aspx?model=U501 ... Hoover U5018-900 Bagged Upright Vacuum
Broken belt My husband and i took apart the vacuum and found out the belt was broken. how do you replace it? we could not remove the area where the belt is.
Hi.\015\012\015\012If you cant easily see how to replace the Belt then I think your Dc07 has A clutch unit.\015\012\015\012This type of Dc07 has 2 belts one from motor to clutch & the second belt goes clutch to brush rolle ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Broken belt I have a royal canister model 4750 with a broken belt on the power head. I don't know how to disassemble the head to get at the belt.
If you have the power head with the headlight, squeeze the sides of the upper part (almost like a superstructure,) where the headlight is located. It should lift off, allowing access to the screws to get the powerhead apart the rest of the way, and o ... Vacuums
Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode
... Hoover Vacuums
Broken belt the belt is broken. how do i install a new one?
... Hoover Soft Light U4266-940 Bagged Upright Vacuum
Is this free? i have a bissell carpet cleaner and i cannot get the soap and water to come out. it will **** up the dirty water however. i just found the belt is broken but i can see no way of how to put a new one in. is a broken belt the reason no soap is coming out?
If it is the flat belt that broke, that is the pump belt, the pump can't work without it. To replace the belts, turn the unit over, remove the red holder, has one screw, pull it out, then the brush roll will come loose. You can replace the belts th ... Bissell Powersteamer 1694 Upright Vacuum
I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums
My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a
... Bissell ProHeat Deep Cleaner Upright Vacuum
A small belt fell from underneath my bissell steam cleaner and I notice the brushes no longer rotate when I purchase the part where does it go? I tried turning it up side down to find out where it came from don't know because there is a compartment for the belt access but that particular bet is not broken. It's a very thin belt I can not make out the number located on the belt please help.
If you are unsure about where it goes it may have a diagram in the owners manual. When you say you saw a belt in a compartment are you sure that it is not an extra belt you are seeing as they often give an extra in the machine kept in a compartment l ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
I have a 20 yr old upright U4689-910 with a broken agitator belt. I have a replacement belt. I have removed the L shaped plate on the bottom of the vac. It is not clear to me how to replace the belt at this point.
If it is like the older hoover models you need toDISCONNECT FROM MAINS FIRST then lift out the roller with the brushes on it, grip firmly at both ends and pull away from body of hoover, loop the belt over it and push it back in. Make sure you l ... Hoover Vacuums
For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.
... Kirby Ultimate G Bagged Upright Vacuum
I have a Dirt Devil Swivel Glide Vac with a broken belt. I have purchased the correct belt(#4).The bottom is off and I cannot tell where the belt connects to. Please help. Jann
It connects to the left side with the little metal rod sticking out.then connect to the wooden roller. in the space without the brush on it. roll the wooden piece to check if everything moves. then put back together. ... Dirt Devil Vacuums
We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.
I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums
I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.
The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I changed the belt on my bissell Cleanview revolution 3596 twice and both times the belt burned and starting to smoke. I'm not sure what to do now I have two broken belts what could I be doing wrong?
Sounds like the brush that the belt runs (or is supposed to run) is being kept from turning. If you can get the brush out to clean it and lubricate the ends that go into the holder clips, this should solve the problem.\015\012With the new belts burn ... Bissell CleanView 3596 Bagless Upright Vacuum
I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum
Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.
You need a new belt. ... Vacuums
Hi I have a dirt devil vision. Hose works, but does not vacuuming the floor. Belts are not broken. Larger belt is moving, smaller belt that moves the brushes does not.
Hi krueger, sorry for the problems but hers an idea how about turning on the vacuum and put your hand under the part where it sucks uo the dirt off the floor and i guessing you would have a little suction, since the brushes are not moving its going t ... Dirt Devil M086700 Vision Bagless Upright Vacuum
I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha
I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Belt is intact and belt is not broken but won't work when turned on.
... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson dc19 ts turbine belt is broken
Kenmore progressive model 38812790 smelled like rubber burning then the brushes stopped turning. Does it have a belt, if so, how do I get to broken belt to replace?
... Kenmore Vacuums
Belt pulley is broken
Sad to say but as far as i know you cannot get any parts for dirt devil vacs only filters and belts and bags sorry ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
Beater bar will not turn, think belt is broken, but do not know
The model number of the powerhead would be helpful - usually there is plastic cover with a lens for the light, push inward on both sides and the cover will pop offthere are two screws under that OR, there are two screws on the underside of the unit - ... Kenmore 25512/ 25513 Progressive Canister Vacuum