Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

Re-connecting Vacuum Head

\015 I took the vacuum head part off of my vacuum and I can't figure out how to put it back on and re-connect the belt the right way. It's driving me crazy!\015

Answers :

On the kirby head is a square knob with the kirby name on it. use your finger and pull out the belt and rotate the knob until the metal pawl engages the belt. keep turning until it stops. the belt should be in the correct position to install the head. place the whole head onto the lower two tangs and lift up. now rotate the wedge clamp until it stops. then rotate the belt lifter till the knob is straight.
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the Miele S175i Powerhouse Plus and it vacuums fine, but the bottom piece of the vacuum is broken. The head of the vacuum swivels freely and doesn't lock into place. Also, the connecting belt is messed up. How can I fix the head so that it doesn't swivel freely?


... Miele S175i Bagged Upright Vacuum

I have a kemore progressive canister vacuum and the power head connects enough to the hose where the head accnoledges it's connected and the brush spins BUT i can't get it to lock in so i have


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Kenmore Progressive vacuum cleaner head continually shuts off when wand is turned. Seems to be a short in the connection between wand and vacuum head?


Go to wallmart and get new one take the old one put in new box get your money back drive back home and get some vaccumeing done ... Vacuums

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.


Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Re-connecting Vacuum Head


On the kirby head is a square knob with the kirby name on it. use your finger and pull out the belt and rotate the knob until the metal pawl engages the belt. keep turning until it stops. the belt should be in the correct position to install the head ... Kirby Ultimate G Bagged Upright Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto


Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

I have a Wertheim 4808 Barrel vacuum cleaner that has suddenly stopped working. I believe that there is a problem with the electrical cord connection inside. I have tried unsuccessfully to open the compartment that leads to that area. One side unscrewed with a phillips head screwdriver but the other side seems to have a different type of fixing screw that I am unable to undo. It is awkward to get at and in a deep slot and the head of the fixing screw? is not visible.


... Vacuums

Power Head keeps cutting in and out while vacuuming???Canister motor keeps running but the power head starts and stops like there is a short or some loss of connection somewhere. Any ideas?


My kenmore progressive vacuum had the same problem. The electrical terminal at the bottom of the wand was corroded. I used a flat head screw driver to scrape the female portion of the connector as best as I could. I then took off the plastic cover on ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

MODEL EL4050 VACUUM AND WAND WILL NOT CONNECT When I use the vacuum the wand and the head become disconnected. They do not lock up.


... Electrolux Vacuums

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Need the extention part that connects to the vacuum head,


Hi the only place you can get these from second hand would be ebay but failing that you could try an electrical repair shop in your area and you should find they will have loads of these lying around and should give you one for next to nothing. ... Vacuums

We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?


Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum

I have an electolux EL7001 canister vacuum. When I attach the large power nozzle....the one for the carpets not the small one for the floors...the nozzle is not powered unless I strap it on with duct tape. Is there some piece I can purchase that will secure the connection between the wand and the power nozzle head so that it is powered without the duct tape?thank you.


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Rod problem... One of the electrical connection posts that are on the top of the rod appears to be broken which causes the power head to work only when it makes contact. Is this repairable? If not, is it replaceable? If not, are the rods available for purchase? The vacuum cleaner itself works well,


You would need a new wand. this might work for your unit. ... Fantom Vacums Lighting Canister Vacuum

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene


... Vacuums

Electrolux EL7024A vacuum power head wiring


... Electrolux Vacuums

I was vacuuming and my electrolux 2100 accidentally suctioned the string attached to a balloon. I turned off the vacuum and unwrapped the string from the head of my vacuum. On the hose i have plenty of suction but the head isn't working. i flipped on and off the emergency shutoff switch but it is not working. what happened? what can i do?


... Electrolux UltraLux 2000 Bagged Canister Vacuum

The plastic 'bracket' for want of a better word has been 'snapped' on either side of the vacuum hose entry point to the head of the vacuum. I have the Electrolux Maximus AMX7025 (made in the EU). Can this part be replaced or do I have to purchase the whole vacuum head?


... Electrolux EL4100 Bagged Canister Vacuum

Meile Solaris. Power cord connection faulty. Unit powers on/off when cord is being retracted/pulled out. Maybe a break in wire close to connection point in vacuum. Or, the connection point itself is loose? The problem likely resulted from trying to use vacuum at furthest extent of cord.


Cord reel likely needs to be tightened. requirs disassembly and large washers installed to keep reel connections tight. Jim ... Vacuums

I have a kenmore vacuum and the head of the vacuum is not turning as it should..what do i do? Everything else seems to be working...I tried to reset it but nothing happened. One more thing what is the head of the vacuum properly called?


Replace the belt on the vaccum. ... Vacuums

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?


... Vacuums

I have a tank style vacuum. When I vacuum with the power head it dims and slows down when I push the power head back and forth, but it powers back up louder when I stop pushing it If i remove the powerhead from the hose the vacuum works fine.


Most likely the belt. Thats the cheapest so try it first ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My home has a central vacuum system hook-up but no vacuum installed. My friend upgraded his central system and gave me his Eureka Mega Boss central vacuum system and the accessories, including the pow


The power head requires 120 Volts. Some hoses have a receptacle in the handle for the power head plug, and the hose has a cord at the wall inlet end that plugs into a receptacle. Some hoses have a plug at the wall inlet end that plugs into a 120Volt ... Eureka 1810 Central System Vacuum

The carpet head on my Kenmore vacuum has stopped working. It is a Kenmore progressive vacuum with a whisper belt head.


... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0801 seconds