Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

What do the numbers on the Kirby G5 beater bar end caps mean?

Answers :

The numbers on the beater bar end caps are used to lower the brush down as the bristles wear down. When you bought the machine, the brush roller started in the 1 setting. One year later, after the bristles have worn down, you can move the numbers to 2, then 3, etc.
\015\012It's a pretty neat concept by Kirby, it prolongs the life of the roller brush significantly.
\015\012Hope this helped you,
\015\012Chris Jones
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What do the numbers on the Kirby G5 beater bar end caps mean?

The numbers on the beater bar end caps are used to lower the brush down as the bristles wear down. When you bought the machine, the brush roller started in the 1 setting. One year later, after the bristles have worn down, you can move the numbers ... Kirby Ultimate G Bagged Upright Vacuum

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.

The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?

... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

Bissell 6579-2 bagless vacuum. Beater bar siezed up. motor turns. took bar out, no movement from either end cap on bar.

1. Uing the appropriate sized drift punch, tap out the steel axle rod which passes through the beater drum.2. Each end cap houses a 608ZZ ball brg.3. Check each brg for freedom of smooth rotation. Replace both if either is seized. ... Vacuums

Bad beater bar end bushing for eureka 5860--part number??

... Eureka 5860A Bagless Upright Cyclonic Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

The beater bar on my Kirby Generation 3 does not turn when it is on. I took it off and cleaned it but I am not sure which way to put beater bar back in. The ways I tried, it still doesn't work.

First - make sure that you are installing it right - see online manual HERE . If you still can not get it working right - issue new ticket and explain in more de ... Kirby Generation 3 Bagged Upright Vacuum

I have a Germ Guardian GGU350TT. The Beater Bar Brush is seized up on the ends and no longer rotates. Can it be fixed or can I buy a replacement Beater Bar Brush? I've called the company and they were no help.

... Germ Guardian GGU300 Bagless Vacuum

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane

... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Part numbers for washers and end caps of vacuum agitator brush

The part numbers for the washers and caps can only be found if you know the agitator brush number.  ... Panasonic MC-V5745 Bagged Upright Vacuum

When replacing the beater bar on the Oreck XL upright with a new bar, what way do the words "new" and "old" on the ends of the bar face?

Hello,I don't really understand your question, but I believe you are trying to replace the beater bar of your Oreck XL.... Follow the below instructions on how to replace your vacuum's beater bar:Turn your upright vacuum clean ... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?

So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is

... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.

Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

I cannot get my beater bar to turn - Kirby G4 Bagged Upright Vacuum

Manual on how to attach the nozzle - HERE. Or you may watch the video on the bottom of the home page on goodvac.comGood luck,Rocky ... Kirby G4 Bagged Upright Vacuum

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.

... Panasonic MC-V7515 Bagged Upright Vacuum

How to replace the ends of a beater bar for a hoover vacuum.

Try this site for a good picture of an upright vacuum. (It is upright, right?)EVERY vacuum is different. Most you remove the bottom plate and extract the br ... Vacuums

Possible broken belt - where do I find access to the belt. The beater bar does not rotate when i release the handle. I like this machine, but It is only 2 years old, the warranty has expired. And i must say, I am disappointed I am concerned that this article will end up in the landfill, adding one more problem for the environment.

As you do not say which type of vac ? but assume definately upright hoover/dyson or similar ? the actual belt is not difficult to renew on either model/s at this stage can only suggest you turn vac over to reveal the cover that houses the ro ... Vacuums

Need to change the belt on my kirby model 519, assuming this is the problem since the beater bar is not turning and I can smell burning rubber

The beater bar is jammed--usually from thread, string, and hair that is wound up on the bar and particularly on the bar end bearings. The bearings themselves usually require cleaning and re-oiling. The belt may be damaged sufficiently to require repl ... Vacuums

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.

It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

How do I replace belt on hoover s1147 twist & vac? I know it goes on the middle of the beater bar but I cant see where to attach the other end to.

... Hoover S1147 Twist Vac Handheld Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

Problem with small belt and beater bar spinning. Where to get replacement belt and what is it called model number. Thanks. Only 2 months old 5780-900 Hoover windtunnel cyclonic

Here you can get a package of the belts you need. Also here is a link to the manual:U5780-900 Belts\015\012\015\012\01 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0700 seconds