Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

Chatter We have a Kirby Ultimate G. Since we purchased it it bounces across the floor and the level of the sweeper has nothing to do with it. To get it to stop, it has to be at the highest level. The place we bought it, has done nothing to help us. We tried a new beater brush, no help. If I have to use it at it's highest level to sweep my carpet, I might as well not waste my time. ANy suggestions?

Answers :

\015\012Posted by CANRN on May 06, 2008
\015\012We have a Kirby Ultimate G. Since we purchased it bounces across the floor and the level of the sweeper has nothing to do with it. To get it to stop, it has to be at the highest level. The place we bought it, has done nothing to help us. We tried a new beater brush, no help. If I have to use it at it's highest level to sweep my carpet, I might as well not waste my time. Any suggestions?
\015\012I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
\015\012Kirby Ultimate G Bagged Upright Vacuum
\015\012The only thing I can suggest is that the brushroll could be in backwards, as you look @ the bottom of the brushroll from the bottom plate, the head of the screws should be facing the floor on each side of the brushroll, so check the brushroll because I thing that is what is happening, what you can do is adjust the brushroll down using the screws doing a ¼ or ½ turn
\015\012Until the brushroll stops bouncing across the floor, once you get it adjusted correctly then raise the height adjustment to the highest level and adjust downward to listen for the tone to change and then try it, it should work and if not go down one more adjustment – also change the belt every 4 to 6 months as recommended by the manufacturer. Feel free to contact a local vac dealer in your area for the brushroll height adjustment if you have problems. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
\015\012For a owner manual contact the Kirby Factory Dealer.
\015\012http://kirby.com Contact Us by Phone
\015\012United States and Canada 1-800-494-8586
\015\012Between the hours of 8:00 am to 5:00 pm EST
\015\012Monday thru Friday
\015\012Don – The Vac Man
\015\012Go Ahead. Use Us.
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Chatter We have a Kirby Ultimate G. Since we purchased it it bounces across the floor and the level of the sweeper has nothing to do with it. To get it to stop, it has to be at the highest level. The place we bought it, has done nothing to help us. We tried a new beater brush, no help. If I have to use it at it's highest level to sweep my carpet, I might as well not waste my time. ANy suggestions?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=576381\015\012Chatter\015\012Posted by CANRN on May 06, 2008\015\012We have a Kirby Ultimate G. Since we purcha ... Kirby Ultimate G Bagged Upright Vacuum

I recently took out a stand mixer that is probably over 50 years old. It belonged to my mother and I wanted to use it. It probably hasn't been used in at least 10 years. With some effort, I removed one of the beaters but cannot remove the other one nor can I even budge it. I have used WD-40 but it's not helping. It's a Westinghouse product. Any ideas? Thanks.

If you used WD40, you should have the unit inverted so the WD40 runs down into the beater socket.Use a small piece of wood and place it against the bottom of the beater and tap lightly with a hammer while pressing the beater release button/lever, jus ... Vacuums

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?

As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Vacuum works fine when using the attachments, but as soon as we try to use it in it's normal upright position it does not work. We have cleaned all filters and removed debris from roller, but nothing has helped.

Greetings,\015\012\015\012There could be a few things that would cause your Dyson to do this. I will give you detailed step by step instructions along with pictures on how you can diagnose this problem. \015\012\015\012Po ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!

... Vacuums

When using my hoover wind tunnel the last few times it has emitted a burnt rubber smell so my husband checked the belt and is wasn't broken or off but now when I use the vacuum the beater bar doesn't seem to be going around as well as it should be can you help

I take it the belt was put back on !! i would say hubbi forgot the tension arm a little black striker that can go in two ways but put in back wards it will not tension the arm ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My shop vac blows dust as soon as it's turned on and throughout use. I have changed filters, nothing is helping. What part of my vac can not get wet, or is there a better way to clean out the system?

There should be a cover or sock over the filter,this will stop the dust.the paper filter is the part that can not get wet. if you don't have a cover for your filter use an old sock or something simular to a sock. ... Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum

Trio model T3000. My touch screen doesn't work. It will turn on and off and it is not on hold. When i touch it, it doesn't do anything. HELP!!! just bought it 2 days ago used it once, tried it again and nothing.

... Vacuums

Dyson 28 airmuscle... carpet level selectors will not stop blinking... I have tried all selectors to see if an adjustment helps It has not lost section but the blinking light tells me something is up... I have two vaccumes one for upstairs and one for downstairs. all same carpet in the house and I use the medium pile and only one of the vaccumes is having this problem

... Dyson Vacuums

The Petmate powerhead roller stopped rotating. I checked for anything binding it - nothing. There is power getting to it, just no rotation. As the guy said in the post above, it's like it is locked into the plastic housing, although it just worked last time I used the powerhead. Help!

... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Dyson animal loses suction when I let the handle down from the upright position to use, I've cleaned the foam filter, and the plastic filter holder and dried thoroughly, removed and cleared the right side U-bend, and the center, rear U-bend access, also made sure nothing was in the way of the beater bar. Any thoughts? thanks. lorri

Is the noise a loud screaming or a grinding/vibration? The screaming is an air flow problem and you'll want to check your hoses are clear and all the seals are tight. The grinding is an issue with the roller/belt/clutch/motor/housing. From what I'm r ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hello! I have a Kenmore Progressive bagless vacuum with the Easy Clean extended life filter. The model number on my vacuum is 34728401. I was vacuuming the carpet when it just stopped running. The dirt sensor light will come on, but nothing else. The belt looks fine, and I don't see anything keeping the beaters from rotating. Help Please!!!

You can have power to the dirt light sensor, but it seems like the motor itself is not using the power supplied. ... Vacuums

I was using my Rigid WD09450 shop vac and the neighbor wanted to borrow it. When i got it back the noise level had increased tremendously. What could have happened.... nothing seems to be clogged and suction is fine. But the noise hurts my ears.

I need instruction manual asap ... Vacuums

I bought the vac, used, but was told there was nothing wrong with it. I called the company, and was given the impression that it will be a huge headache to return it. Here's the best part: when I received it, I opened the box: it was broken. Clearly the highest internal piece of the vacume, whent he handle is removed, was cracked off, and in two pieces. The handle will not lock into place, so if I were to vacume forward, see ya, and the vac is back in pieces. Any idea how to rig this to get it t

... Dyson DC25 Vacuum

Nothing spraying out of Bissell Powersteamer Proheat. I've check filter under flow indicator, pump belt is fine, cleaner in proper tank, bladder of water tank is full. We've had it for a very long time but it's barely been used. Can anyone help?

... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

My Roomba was bought at Christmas 2008 and now April 2009 the brushes that sweep the edges and bring in the crumbs etc...don't seem to be doing the trick...It leaves behind stuff it didn't used to leave especially along edges. Thank you for any help

Have you tried unscrewing the little brush and cleaning underneath? mine wasn't turning properly and when i took it off lots of hair/fur was wrapped around the screw. try this and good luck. ... iRobot Roomba 560 Robotic Vacuum

I recently purchased this vacuum after reading consumer reports article on it and from recommendations from family. However, since I've had this vacuum it's been nothing but problems! I have a frieze carpet and I have the vacuum set on the highest setting. Each time I use it, the vacuum clogs with carpet fibers before I even finish a room! Any suggestions?

Is that a shag carpet? the power head is raised up all the way can you lower the suction on it is the carpet old the vacuum may not be able to handle the carpet,go to a vacuum store and see if you can try somthing else out some stores well let you re ... Hoover Tempo Widepath Upright Vacuum - Blue

My Dyson upright is not picking up like it used to. The suction from the tools is very strong and the beater bar is turning and clean. Please help

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The electricity in the apt attached to my house lost power in two of the walls. It happened when the cleaning ladies I think were using a vacuum, they don't speak english very well so I'm not sure. I have looked at the circuit breaker a # of times and nothing seems to have been tripped. I have also inspected the outlets and they seem to be fine. Can you help me?

Even know the breaker doesn't look tripped it might be. You have to flip it all the way off and then back on again. That is most likely what has happened. If that doesn't work check to make sure a GFI hasn't tripped. They are usually loc ... Vacuums

Lost suction I've only used this vacuum a few times, it's practically brand new. Now, one I turn it on, it sounds fine, and the hose feels as if it's getting some suction, but it's not strong enough to actually **** things up from the carpet into the canister. I have completely emptied the canister and bought a new filter. Nothing seems to help.

TOSS IT and forget it! I have never used a hand vac that worked that was worth the effort of turning it on .... I suggest they are all junk ... I found very few vacuum cleaners ... actually **** especially anything made by dirt devil ... I do have a ... Dirt Devil Vibe AllPurpose Hand Vacuum Bagless Vacuum

Hello. My scooba 5800 had a check tank light on. I used a straw on the valve and that fixed the problem. Now the scooba runs like nothing is wrong, but there is no actual cleaning going on! It goes the full cycle, but no liquid comes out. The vac part seems to be working b/c there is fluff in the vac when it's done. Please help!

Hello, Take the battery out and hold the switch down for 30 seconds, to reset the curcuit board, then charge back up for 12 hours. this should take care of it. If I can help future please call @ 1561-848-3387 Thank you, Teresa. Clean Sweep Vacuums ... iRobot 5800 Scooba Vacuum

My shark just stopped working. It was working just fine last time i used it. Now when I plug it in nothing happens. What can I do, help my floors are crying for attention.

No sound no nothing!!! Well or the buttons, or the wires, is not connecting, unplug and try 2 fix it or call 911 :) Am kidding, or someone who knows about it. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.

First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected und ... Vacuums

No manual Hi there my bissell will not **** up the water its been some time ago that I used it and it has not been used more than 2or 3 times can any one help me with this. I have also miss placed my manual and instruction this does not help me either .So if any one can help Id be a happy woman with clean floors thanx Vickie

Link to the manual download - http://www.bissell.com/Product_Search.aspx?Criteria=1699\015\012CHeck to see if the front of the unit is clogge ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0812 seconds