Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

Can you remove the plastic part on the bottom of the bag or to tighten or is that a crack I see dust blows out of the bottom


Answers :

There is a hand grip built into the bottom of the housing to help remove it. If it has not been removed on a regular basis to dump out heavy debris, it may be stuck. Use a screwdriver as a lever and pry it outward from the motor unit to remove it and inspect for damage. For easy re-installation, wet the seal on the motor outlet. It attaches by a simple bayonet mount. Remember the motor will not run unless the bag assembly is securely installed.
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can you remove the plastic part on the bottom of the bag or to tighten or is that a crack I see dust blows out of the bottom


There is a hand grip built into the bottom of the housing to help remove it. If it has not been removed on a regular basis to dump out heavy debris, it may be stuck. Use a screwdriver as a lever and pry it outward from the motor unit to remove it and ... Kirby Ultimate G Bagged Upright Vacuum

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!


... Miele Vacuums

We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that


Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and sh ... Beam Industries 2900 Serenity Plus Central System Vacuum

Dirt is coming out the bottom of my Kenmore Progressive Upright Vacuum. My husband found a large dust bunny in the drive belt and removed it. He also changed the bag. Why is dirt coming out the bottom? Thanks.


Its still clogged, you gotta dig deeper ... Vacuums

Hoover self-propelled windtunnel U6430-900 flat belt gets hot & becomes hard to push. It has a filter bag. Purchased 8/2/01. Took one plate off bottom. Used a compressor to blow out dirt & dust. Put new thin belt on.


Belts get hot when fibers from carpet get wound arounf the belts mounting shaft. Best to take a razor and cut off any fibers so the belt doesn't get hot again ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Eureka model 2961 does not **** up larger particles. You can see it picks up dust and dirt. Am trying to remove bottom guard plate to check belt but can't take it off.


Here\015\012 is a Link to one of my Tips:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinningThis\015\012 should solve the problem. ... Eureka 2961AVZ Bagless Upright Vacuum

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

The vacuum leaks dust around the joint between the bag and the vacuum. I unlatched the bag, removed and emptied it, and replaced it. However, the vacuum still leaks dust around the joint and the bag keeps working loose. How can I make sure that the bag is securely latched so that it does not leak or come loose? I have no manual. Thanks.


... Bissell 3065 Power Partner Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug


Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Im trying to replace the cloth bag on my Kirby G6. How do I release the belt that holds the cloth bag at the bottom of the assembly? It is grey and has teeth that grab when tightened on the bottom of the unit.


Kirby G6\015\012Im trying to replace the cloth bag on my Kirby G6. How do I release the belt that holds the cloth bag at the bottom of the assembly? It is grey and has teeth that grab when tightened on the bottom of the unit. ... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!


... Miele S7210 Bagged Upright Vacuum

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.


If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

I have a BC-A41 vacuum cleaner which has been working well, but now it appears to blow stuff away from the cleaner as I hoover. I find the hose packed up with stuff, but no content in bag. I recently changed the bag...could it be that the bag is not fitted correctly..I am puzzled by the instruction to put the bottom under the rib. I am a pensioner on my own, and would welcome any help. Thanks, Jim


I think there should be some probem in the vacuum section..its failing to **** the objects ... Vacuums

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

Hi, I have a Dirt Devil Model # M08100REDC. I desperately need to change the bag, but I don't see an obvious way to do it. I'm afraid to try pulling on the cloth tab thingy that's just below the handle, between the rubber ring that holds the bag on the vac, because it seems like stuff will fly everywhere from the force required to remove it, and I might not be able to get it back on there. Should I just pull on that cloth tab until the bag comes off? Thanks, Roberta


You can pull on the tab to remove the bag, but probably a better way is to gently pull on the rubber ring that attaches the bag to the back of the vacuum body. If you don't yank and ****, it should come off without spilling the dirt. There may also b ... Dirt Devil Classic M08100 Bagged Handheld Vacuum

I have a G4 and the plastic at bottom of bag is cracked


Hi There,Well sort of. For the G4, the bottom boot is sold with the internal fill tube that inside of the outer bag, where the paper bag connects. These two parts are sold complete as an assembly already put together. You'll just nee ... Kirby G4 Bagged Upright Vacuum

Not sucking from bottom into bag, but blows out the side filter,..yet it DOES **** FROM HOSE ATTACHMENT. How can this be?...the.belt is fine recently replace, the rollers clean..I can feel anything i


Here is a diagram ,it's probably the hose behind the brush bar thats blocked.http://www.vacsite.com/en/bissell-parts-1/bissell-parts/3522-powerf ... Bissell 3522 PowerForce Bagged Upright Vacuum

How to remove the hinged plastic piece at the bottom of the bag?


... Oreck XL Ultra Bagged Upright Vacuum

My nilfisk action sucks for a few minutes then over heats and sometimes blows dust out and the bag explodes. The pipe is not blocked and I have cleaned filters and put a new bag in but still thesame thing is happening


Their has to be an obstruction in the system causing this issue ... Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

When I turn on my Kenmore Premier 4.5 Peak HP 10.0 Amp after about a minute of running I get a burning smell. When I opened up the compartment that holds the dust collection bag, and remove the bag I found a filter. The filter was minimally dusty and has been cleaned. After sniffing around, I could not identify the source of the smell.


Dose it smell like rubber check your belt ... Vacuums

Need to remove bottom cover of Panasonic MCV7314 vacuum to see if the belt is broken. I can't figure out how to remove and can't find a manual online.


I did a search for the manual for that model and found a pdf file online that had instructions and pictures. It was still slightly different and hard to get off. I took out two screws and then held in two side "clips" and wrestled it off. I dont t ... Panasonic Vacuums

I cant get my kirby to blow out...bag is removed from seating...its plugged in...i attach the hose to the place where the bag goes, but it wont run


I did get it to work! It was a struggle, but It finally hit that hidden switch just right. The hose attaches to where the bag goes, and it just wouldnt seat properly. I suppose there might be some wear there on the hose end that twists in . ... Kirby Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0539 seconds