Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

Kirby hoover can you tell me hop i get roller of head to fit new belt. many thanks

Answers :

Turn the latch to release the nozzle as. Take off the bottom plate, remove the brush roll, check it while you have it out, put a new belt over the brush roll and reinstall back into the nozzle, belt should be in the center, put the bottom plate back on. Then turn the big knob on the front until it stops, this gets the belt ready to install. Reinsatll the nozzle back onto the vac, latch it, then turn the knob back the other way and the belt will be on the pulley and you are set to go.
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby hoover can you tell me hop i get roller of head to fit new belt. many thanks

Turn the latch to release the nozzle as. Take off the bottom plate, remove the brush roll, check it while you have it out, put a new belt over the brush roll and reinstall back into the nozzle, belt should be in the center, put the bottom plate back ... Kirby Ultimate G Bagged Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel

The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Trying to fix new belt to Hoover Turbo Power vacuum cleaner. Don't see how the belt becomes taut. Fitting it around the roller, there is nowhere to fit the belt to, it just sits loose.

I looked at the user instructions guide online and saw where the 'other end' of the belt should be fitted. It was extremely hard to fit but eventually managed it. Thanks for this solution site. I wouldn't hesitate to use it again. ... Hoover U5396-900 Turbo Power Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.

The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?

If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.

I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Just tried to fit a new belt to a vax quicklite 2 upright hoover and the belt snapped is there a right way to fit belt

... VAX Appliances Vax X3 Bagless Upright Vacuum

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.

Model no. req ... Hoover Vacuums

My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.

Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.

... Hoover Vacuums

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]

Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My belt broke on my kirby upright, I took the roller off and put the new belt on, but I cant get the hook to hook on the belt.

On the front of the nozzle is a big knob that you turn to load the belt. Take the nozzle of of the vac, turn the knob to catch the belt, keep turning it until it stops. You will know if the it caught the belt, it will be hard to turn. Put the nozz ... Vacuums

The roller on my power head does not spin consistently. So my vac is not picking up of course. The square end pieces and the rod that goes into the wooden roller seem loose. I tried tightening it but it still is not turning. Can I do a fix with glue or something till I can get a new roller?

... Rainbow E series Canister Wet/Dry Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]

The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

DC 17 animal, axle roller that acts as a belt tensioner is shot, including the plastic mount that it sets in, (poor design) that wore down when the roller froze up. Where can I get just this part without having to buy the whole brush head assembly? Do they have one that is metal? Not the roller the mount for it>

I've had this stupid problem and my $500 dollar vacume has been broke for months so today after I spent hours on hold at dyson and talking to sears and everybody else under the sun and they say part doesn't exist pretty much, so finally I talk to a d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My fan belt on my hoover is broken,where is it located and how do i fit a new fan belt

I figured out on my hoover upright that many of those models don't access the belt by removing the plate under the vacume. the housing top actually prys off (with the help of a flathead screwdriver). step on the handle release button and lay the ha ... Hoover Vacuums

Hoover self-propelled windtunnel U6430-900 flat belt gets hot & becomes hard to push. It has a filter bag. Purchased 8/2/01. Took one plate off bottom. Used a compressor to blow out dirt & dust. Put new thin belt on.

Belts get hot when fibers from carpet get wound arounf the belts mounting shaft. Best to take a razor and cut off any fibers so the belt doesn't get hot again ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!

The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0994 seconds