Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?

How do you install the belt on the kirby vacuum?

Answers :

Step 1: 
UNPLUG YOUR KIRBY VACUUM CLEANER. Before you go any further, take your time with this belt change. It's not that difficult, just a little different than most other vacuums. These belts are very easy to find on the internet.\015\012kirby-oldstyle1.jpg\015\012\015\012Step 2: 
You should be facing the front of your Kirby vacuum. The height adjustment lever will be on your right. Push the lever all the way down. Lift the light hood with your left hand. Turn theKirby vacuum belt lifter counter-clockwise with your right hand. Unlock the accessory lock. The accessory lock is located under the light hood. Move the lock to the left to disengage it. Remove the front of the vacuum cleaner.
\015\012kirby-oldstyle2.jpg\015\012\015\012kirby-oldstyle2a.jpg\015\012\015\012Step 3: 
Turn the vacuum belt lifter all the way clockwise until the belt drops down. Unlock the roller plate by releasing the two latches on the rear. Pull the roller plate up slightly and then off.\015\012kirby-oldstyle3.jpg\015\012\015\012kirby-oldstyle3a.jpg\015\012\015\012 
Step 4: 
Bend one end of the roller bracket just enough to remove the roller. Remove this end of the roller. If you need to replace the roller take it all the way out. Remove any carpet fiber, string, or hair from the roller with a scissor.

\015\012kirby-oldstyle4.jpg\015\012\015\012kirby-oldstyle4a.jpg\015\012\015\012Step 5:
After you have removed the old belt, slide the new one back on the middle of the roller. If you're Kirby vacuum cleaner has a belt indicator light, the roller will have a magnet built onto one end of it. It's very important to install to install a roller with a magnet on the same side as the indicator light. The roller actually will only fit into the roller plate one way.
\015\012kirby-oldstyle4.jpg\015\012\015\012Step 6: 
Place the roller back in the roller bracket. Place the roller bracket back and lock it into place with the 2 latches. Rotate the vacuum cleaner belt lifter counter-clockwise. You should feel the the belt catch. Look inside to make sure the belt is being stretched onto the vacuum belt lifter. Reassemble the machine. After you have reassembled your Kirby, turn the belt lifter cockwise, releasing the vacuum belt onto the vacuum motor shaft.\015\012kirby-oldstyle2.jpg

Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to install KIRBY belt lifter HOOK Assy - Kirby G4 Bagged Upright Vacuum

Hello, saI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would take ... Kirby G4 Bagged Upright Vacuum

Install kirby belt 301291 - Kirby Ultimate G Bagged Upright Vacuum

I just figured it out myself.\015\012\015\012Thanks ... Kirby Ultimate G Bagged Upright Vacuum

How to install a belt on a Kirby 3cb - Vacuums

... Vacuums

How to install the belt on the ultimate g kirby vacuum

Hello,take a look at this link:http://www.goodvac.com/articles.asp?id=143Good luck,Rocky ... Kirby Ultimate G Bagged Upright Vacuum

How do you install the belt on the kirby vacuum?

Step 1: UNPLUG YOUR KIRBY VACUUM CLEANER. Before you go any further, take your time with this belt change. It's not that difficult, just a little different than most other vacuums. These belts are very easy to find on the internet.\ ... Kirby Ultimate G Bagged Upright Vacuum

How do I install a new belt on my Kirby G3D Vacuum

... Kirby Ultimate G Bagged Upright Vacuum

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!

Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

How to install the belt ajuster on Kirby Ultimate G

Watch this video ... Kirby Vacuums

Installing belt How to install a belt on Hoover upright vacuum

Here are the step by step instructions from the owners manual for your machine.\015\012\015\012\015\012Disconnect cleaner from electrical outlet.\015\012WARNING: Agitator brush roll can start suddenly. Unplug cleaner before turning it over.&nbs ... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

How to change belt on kirby heritage vacuum - Kirby Heritage II Vacuum

... Kirby Heritage II Vacuum

How do i install a belt for a turbo cyclonic upright hoover uh7005 i already bought 5 blets for this vacuum and three of them were burnt i have 2 more belts left and i want to be sure i am doing the installation properly.

... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

How to put on a kirby vacuum belt - Kirby Vacuums

The emblem on the front of the Kirby vacuum controls the installation of the belt. Rotate this emblem. ( I do not remember which direction it rotates). This relieves the tension on the belt. Replace the belt and rotate the emblem back to lock it ... Kirby Vacuums

Where can I find kirby heritage vacuum brush belt 301282 and the vacuum bags for a 1984 kirby heritage?

... Vacuums

Belt installation How do you install a #5 replacement belt on the Dirt Devil upright vacuum cleaner?

One end of the belt will go over the motor drive shaft and the other end will slip over the roller brush. Also, you can find this belt at www.vacbelts.com. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.

Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

Belts I have recently bought new belts and when I installed the green light only comes on sometimes and I can smell rubber burning. The last belt broke very quickly so I am assuming that when I put the vacuum back together I am doing something incorrectly. Can you help instruct me?

Recently received a kirby from mother in law and don't how to change the belts ... Kirby Ultimate G Bagged Upright Vacuum

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

My oreck throws off and burns belts. i install a new belt and it runs fine, but as soon as i try to vacuum the carpet, it burns the belt.

... Oreck XL Ultra Bagged Upright Vacuum

Kirby Sentra vacuum burning belts

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=565459\015\012Generic problem for all Vacuums\015\012Kirby Sentra vacuum burning belts\015\012posted by ... Vacuums

Where do I install the belt on the miele s185 upright vacuum?

... Miele S185 Powerhouse Bagged Upright Vacuum

Installing belt on hoover self propelled upright vacuum

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40544&thid=641399\015\012Installing belt on Hoover self propelled upright...\015\012Posted by Fryeburger on Jun 02, 2008 ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Burning smell There is a burning smell when I run my Kirby Ultimate G.  The smell seems to be coming from the belt.  I looked at the brushes and they are spinning so the belt is working.  the Post on the vacuum is getting very hot not sure if that is normal.  What is causing this?

Unlock the sweeper brushes and take them out. on each end is a cup bearing and should be free of debris.then check around and under the belt and likely there is debris wrapped around it.the post is getting hot as your pulling too much of ... Kirby Ultimate G Bagged Upright Vacuum

How to install Kirby g4 fan - Kirby Generation 3 Bagged Upright Vacuum

It needs to be stripped completly down, if you are confident at doing this then here goes.\015\012It has been a while for me so take your time and some of the steps may have to be completed slightly differently.\015\012Isolate / unplug t ... Kirby Generation 3 Bagged Upright Vacuum

Belt placemaent do you have a diagram showing the proper placement of the belt and how to engage. not my vacuum, and very new to the kirby. thank you. Becky

There is a great video on youtube showing how to do thisIt's not nearly as hard as they say at the beginning.look up "govacuum kirby belt replacement"http://www.youtube.com/user/GoVacuums?v=At7tqnjD-Kc&fe ... Kirby G6 Bagged Upright Vacuum

I need to replace the belt on my kirby. - Kirby Ultimate G Bagged Upright Vacuum

If this is like my Kirby, there are colored slots on each end that slides the brush in and out and they are different sizes but the belt is connected in the middle. First take the bottom cover off. It should be made out of rubber and metal, and it po ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1104 seconds