Having problems with your Kirby vacuum ?

How do I repair handle from falling

Handle falls in storage

Answers :

Repair Help & Product Troubleshooting for Kirby vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I have a Dyson 15 "the ball". The beater bar will only rotate if the vacuum is engaged and the handle at a high angle. The bar stops when I drop the handle to a lower position. The condition is repeatable. Can you provide part and repair instructions?


If air is leaking in somewhere, you will not have any suction.\015\012\015\012\015\012Also there are some possibilities that has to be checked to confirm the fault.The problem is minor but the possibilities are too much for this pa ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

THE HOSE IS BEGINGING TO TEAR AT THE POINT IT CONNECTS TO THE HANDLE. DO I HAVE TO BUY A NEW HOSE OR CAN THIS BE REPAIRED? IF IT CAN BE REPAIRED HOW DO i DO THIS?


If you have a power head that the power flows through the hose you should not try and repair unless you are a service centre other wise most of the time you end up buy a new hose\015\012but if it is not to bad some people just duck tape it ... Broan-NuTone CV353 Central Vacuum

Vacume did not come with screws to hold handle to Vacume need the screws handle falls off vacume hits the floor [email protected] Model # 3041 Type - B2 The answer is simple, send the screws please this will fix the problem. Thanks Dr.Tracy Massie Dr.Tracy Massie Harvard;Dr/PHD; Chief Officer of Internal Medicine;Lead Surgeon Dr. Child Disorders; Princeton Dr. / PhD.; Chief Medical Officer; Lead Councilor


... Eureka 3041BZ Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Bissell 35962 Cleanview Bagless Revolution Upright Vacuum hose is clogged with sock where hose meets handle attachment. Attempted to use broom handle to push back through suction opening. Sock is compacted. Any home repair advice?


If you have access to a small sink "snake" used to clear clogs in sinks, you might be able to use it to "snag" the sock and pull it out.\015\012Needs to be a metal sewer snake so that you can tug on it if and when it snags the sock. ... Bissell 35962 Cleanview Bagless Revolution UprightVacuum

The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?


... Euro-Pro NV31 Infinity Vacuum

Repair hole in hose near handle, can't get handle assemble apart


Hello There,\015\012\015\012We've actually shot a video on how to repair the hose on the kenmore vacuum cleaners. The repair we show in the video is different from yours, but the video will clearly show you to pop open the handle assemb ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hoover floormate handle release pedal broken. Need diy repair information.


... Hoover Vacuums

Repairing contacts in Electrolux Z8240 handle


Hi There, Alec From VacuumSpot here. I work as a vacuum technician and unfortunately I am the bearer of bad news the handle is not really repairable. Even in warranty Electrol ... Electrolux Vacuums

How to repair the elecrolux vacuums z1660 handle


... Electrolux Vacuums

Oreck upright handle falls over


... Oreck XL Ultra Bagged Upright Vacuum

Handle falls back on kirby vacuum


You need to change handle holder (the one with spring at the bottom of handle), mostly spring disconnected and it can,t be fixed. ... Kirby G6 Bagged Upright Vacuum

My Oreck Upright will not stay upright! The handle falls over everytime I leave it stand on its own.


What you are in need of is what they call a detent. There is a possibility that is has broken off from the housing which means that the only way to repair it properly is to replace the entire housing. It may have just had the screw come loose and h ... Oreck XL® Classic Bagged Upright Vacuum

How to repair a g4d vibrating noise in handle


... Kirby G4 Bagged Upright Vacuum

Hoover Mod U8146-900-When you press handle release lever vacuum falls down it doesnt stay up


... Hoover Vacuums

Bissell 9535 How do you repair the Bissell 9535 handle release lever?


I decided to just take it to a qualified repair place. ... Bissell Vacuums

Knob has broken where you remove dirt container. Also the handle . How can I get the container out and what will it cost for repair parts? Model # CP-CY4201E


... Kalorik Red Cyclone Vacuum Cleaner

Regarding my Kirby Generation 3 upright vacuum cleaner: the handle does not lock into place, but rather falls to the floor. Any thoughts on how to get it to stay in place? Also, I lost my owner/operator manual. Can I download one to learn how to clean and maintain the vacuum?


The plate that catches the handle to lock has a hidden spring behind that plate.I would leave it alone for the unit is pressed together. Used ones are found most everyday on Ebay. The owners manual maybe found on this website\015\012\015\ ... Kirby Generation 3 Bagged Upright Vacuum

DC 18 When I try to put it in the closed position, it does not catch, so the handle falls back. Where do I take it to be fixed or what do I do?


Try a new pedal plunger http://www.youtube.com/watch?v=r0ZaqymChXo ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

My Dyson DC17 Animal Bagless Upright does not click to stay in an upright position. It works but the handle falls to the floor.


This is a common fault with the Dyson DC07 (and other Dysons) unfortunately the clip that holds the handle upright hs broken. It can be repaired, but will cost a reasonable amount to have done... I would just live with the problem and prop the vacuum ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi. I purchased a Simplicity Freedom about 2 years ago. I have had it in for various repairs several times. One persistant problem that the repairman cannot seem to fix is the dirt does not fall down into the bag - it just stays up around the suction hole. I only use simplicity bags. Any suggestions would be most appreciated. thank you


You can let the vacuum run alittle longer so the bag fills up with air, also make sure that the bag in on correctly and you have the right bag for the unit. Let me know if this helps. ... Simplicity Vacuums

Stand up lever is plastic, broke when stepped on to release handle, can it be repaired, replaced with a better one, plastic breaks too easily?


The pedal release can be replaced but the base will need to be checked for cracks as well. if the base is broken most common is the socket the pedal release snaps into. some of the plastic parts have been made with better materials ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I bought my [email protected] my local Wal-Mart. It is literally falling apart. The sweeper has NOT been abused. Yes, we have 2 cats & a dog but the problems I am having w/ it should not be warranted. The handle has broken. The wheel/roller on the bottom of the machine has broken off & now it has just stopped working. I repeat, this vacuum has NOT been treated badly @ all. I can not be w/out a vacuum. Thank you for your help, hopefully. Debi


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=729453\015\012Generic problem for all Vacuums\015\012I bought my [email protected] my\015\012Poste ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0279 seconds