Having problems with your Kirby Vacuums ?

Replace wheel axle on my kirby g3 vacuum. have a

\015 I took apart wheel and axle and can't get it back together, don't know where the little spring goes exactly. just thought of taking off the wheel itself to put it back on, that'll probably work, but still don't know exactly how it fits on properly.\015

Answers :

The spring goes inside that pedal that you step on to advance the height. Place that spring in that pedal and then place the pedal into its' groove, then put the axile and wheel assembly over the pedal and put your screws back into the mounting sections.
Repair Help & Product Troubleshooting for Kirby Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace wheel axle on my kirby g3 vacuum. have a


The spring goes inside that pedal that you step on to advance the height. Place that spring in that pedal and then place the pedal into its' groove, then put the axile and wheel assembly over the pedal and put your screws back into the mounting sect ... Kirby Vacuums

The right front wheel came off my G6 Kirby vacuum, then the entire axle and wheel adjustment came loose--including a spring that was attached to something.


Thank heavens for a husband who can fix anything--and save me a lot of money for repairs and advice! ... Kirby Vacuums

HOW DO I REPLACE MY REAR WHEELS ON MY KIRBY G6...I WAS ABLE TO TAKE IT OFF BUT NOW WHEN I INSTALL ONE THE DRIVE SHAFT IS TOO SHORT TO INSTALL THE OTHERE??? PLEASE HELP


Try equalizing the space between the two wheels and the drive shaft. If it's not equal, they may not fit properly, or at all. ... Kirby Vacuums

How do you replace the blower wheel on a kirby G4 vaccume


Hello, onoI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would tak ... Kirby G4 Bagged Upright Vacuum

I need to replace the rear wheel on my kirby. i can't figure out how to remove the little c-clip.


Hello, pazI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would tak ... Kirby G4 Bagged Upright Vacuum

Replacement wheel I broke the wheel on my bissell upright model 3760 and need a replacement wheel and possibly an associated side molding. I can't seem to find replacement parts such as these- any suggestions?


The rear number is 2036627, there is no side casing, you would have to replace the whole back, which Bissell isn't making avaiable. But o get the wheel, you might try bissell.com and see if you can order direct, or try a local repair shop to see if ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Kirby G5 rear wheels lock up completely when in "Drive"


When wheels lock when vacuum is OFF - it is normal. If it happens when Kirby is ON then there are a few things that may have gone wrongPrimary drive belt is broken or something is wrong with plastic gears. See how to check the primary dri ... Kirby G5 Bagged Upright Vacuum

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?


The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

Polti 2400 I am trying to remove the casing from the steam cleaner to fit a replacement wheel. The screws holding the casing are similar to torx but they have a raised centre which means they can't accommodate a torx screwdriver. I thought this was going to be easy just replacing a snap-in wheel!


You can buy T15 torx driver with hole in them from link below. ... Polti Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Belt replacement i am trying to replace the belt on my kirby g4 and i can not get the rooler off to replace the belt. if you could tell me how to do this it would be great.


Lift the light bulb housing up and you will find a latch that will rotate to release the front agitator housing and remove it from the machine. On the bottom of that housing, there are two latches that secure the bottom plate that covers the roller. ... Kirby G4 Bagged Upright Vacuum

How to replace wheel bracket on dirt devil. I have a dirt devil swivel glide and I took off the wheel bracket to clean out a clog and now I cant seem to get the wheel bracket back on.


... Dirt Devil SwivelGlide Bagged Upright Vacuum

Hoover wheel assembly replace wheels - Hoover Fusion Vacuum Front Wheel Carriage 93001674


... Hoover Fusion Vacuum Front Wheel Carriage 93001674

How do I install the front wheels on a kirby sentria G10D? One of the front wheels broke completely off so I ordered the front wheel shaft assy but I didn't remove the broken one so I am having difficulty with how to put the new one on.


... RTO Vacuums

Replacing Front Wheel Assembly


... Vacuums

Fan and bearing replacement on a Kirby G6


If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

Have a dirt devil breeze that the adjust. wheels fell off while replacing the beatter brush. can't figure out how to put the wheels back on


... Dirt Devil Breeze Bagless VacuumVacuum

Lower wheels for low carpet pet lover cannot lower inside wheels to replace adjustment knob


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Ambassador 111 Electrolux canister vacuum, model C101H, how do you replace a back wheel?


... Electrolux Vacuums

Kirby vacuum I have a G 6 kirby vacuum. The power cord has been checked and has continutity and replaced the power switch and the vacuum will still not run


There are 2 safety switchs, one on the front that the nozzle activates, and one on the side that the bag asembly activates. The motor brushes and/or armature maybe bad. ... Kirby Ultimate G Bagged Upright Vacuum

How to replace kirby generation 3 switch? - Kirby Vacuums


I am a trained professional with all the tools & experience and this is a job that would take me 2 hrs. Do your self a favor and take it to your local vacuum shop.It'll probably run you around 200 dollars , half parts and half labor. You pr ... Kirby Vacuums

The belt on my Kirby G3 wore out, and I bought replacement belts from two different sources--one an official Kirby supplier and one a store brand. Neither belt is long enough to catch the belt lifter when it is rotated and to reach the drive shaft.


Kirby has only had 1 belt from day one. sometimes you do need to push the belt up to catch the belt lifter ... Kirby Generation 3 Bagged Upright Vacuum

Replacing propeller Kirby G5: ordered a new propeller and can't seem to open up the unit to replace it. We've found all of the screws (we believe). Are we missing something?


This will help you out tremendously...\015\012\015\012http://reviews.ebay.com/KIRBY-VACUUM-RE ... Kirby G5 Bagged Upright Vacuum

I need to replace the belt on my kirby. - Kirby Ultimate G Bagged Upright Vacuum


If this is like my Kirby, there are colored slots on each end that slides the brush in and out and they are different sizes but the belt is connected in the middle. First take the bottom cover off. It should be made out of rubber and metal, and it po ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0693 seconds