Having problems with your Kirby Vacuums ?

Need to know how to remove fan from my vaccum.


Answers :

Repair Help & Product Troubleshooting for Kirby Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to know how to remove fan from my vaccum.


... Kirby Vacuums

Kirby Heritage II 2HD Vaccum Cleaner. I have removed the housing and reached the motor shaft for the vacuum fan. How do you remove the fan from the shaft.


Hi, you can visit this site to view how to remove the fan from the shaft...http://www.diyonline.com/servlet/GIB_BaseT/diylib_article.html?session.docid=1678Take care ... Vacuums

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?


They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

I need to know how to remove the dirt container on the eureka bagless vacuum. It says that it is easy to remove, yet we cant figure it out. is there some trick to it that we dont know?


There is a lever at the bottom of the dirt cup,turn it to the left and pull out the dirt cup.note while you have the dirt cup out make sure you clean all the filters there is one right above the dirt cup pull out on the right side and there is a filt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Bissell ProHeat Clearview Steam Cleaner - need steps to clean the clear input area. I have removed the four screws and need to know how to finish the removal of the clear plastic input area.


For the clear outer nozzle, there are 2 screws holding it in place. Remove those, then from the bottom lift it up. Sometimes the seal holds it really tight and you may have to carefully pry on the sides until it loosens up. Then when you put it ba ... Bissell Vacuums

Good morning. My elderly parents bought a Kichler ceiling fan for their living room 2-3 years ago - it has a remote and a globe design with a vive. The globe does not have any visible external nut to loosen to release the globe to clean it - the globe is screwed into the vine design which is attached to teh fan. I do not know how to easily remove the globe to clean it - do I have to ds=ismantle teh fan. I checked Kichler's site for over an hour - this may be discontinued.


The globe should be screwed in place by about a quarter turn ... Vacuums

Hello. We have an electrolux super J canister vaccum. Its fan is broken. How can I remove the fan from the motor axel ?Where can I get a new fan ? Looking forward to your reply, Robert


Japanese AV ****, Asian Femdom, Slave Domination & Bdsm\015\012\015\012http://www.avbondage.com ... Electrolux Vacuums

Have Fresh Aire 2.1 about 4 years was running great then went dead. I cant find where the fuse is and have unit apart. I plug in no fan dim display shows to errors. Unit was pretty dirty at the time. I need schematic and suggestions. Also need to knpw how to remove the honeycomb from the light unit to check for blown bulb. Seems brittle and I could break it with trying to pry with augur or sharp screwdiver object.


I'm sorry this may only be a partial help. But fuses are usually very close to the motor, OR where the switch is located. Pretty easy to find by testing but you have to be or so careful you dont electricute yourself. Now if your testing shows v ... Vacuums

I think I need to replace the main battery in my small floor vac - the one that can be hand held like a dust buster or work like a small floor vac. I need to know how to remove the battery and replace it with what kind of new battery..


I see my sense of humor is not appreciated...it was only a joke. Anyway, here is what you do: First, slide the battery cover off the bottom of the hand held unit. Remove the battery from the motor housing by pressing the tab on connector “A&rdq ... Vacuums

I need to know how to put together a Hoover Slider vaccum. I had to take it apart and now i need to put it back together.


... Hoover S2105 Slider Bagless Stick Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

I have a D4 Rainbow and need to know the order of the fans in the lower and upper housing and which way they need to be placed, spacing etc. Any help would be greatly appreciated.


... Rainbow Technologies D4 Bagless Vacuum

I have a Honeywell HF810 fan. I am trying to clean it. I removed the phillips head screws, but their are two odd screws that require a special tool to remove them . I also have to go through the plastic shaft, so I need a special type of screwdriver and a special type of head. Thanks for the challenge!!


... Honeywell Vacuums

How to disassemble electrolux ZAM 6280?i had already removed screws and don't know to disassemble it. i need to check fuse or if it needs resetting.i'm using it and it suddenly stopped completely.no power at all.


Hi There.. I had the exact same problem with my ZAM6280 model. The PCB part (location C8) had blown. Do you know the details for that part, so I can replace it? Otherwise, you didn't happen to come across any schematics for the PCB Module?? ... Vacuums

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?


Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

My son spilled mica all over my carpet. To clean it I used my bissel vaccuum. Now I have orange mica in the removable filter area as well as up inside the part that spins. I need to clean it out, but don't know how to remove it from the vaccuum


Load it into the trunk of your car, take it to a gas station and use the tire inflater hose to blow all the **** out of it.\015\012May have to get a tire stem in order to use it as a blower. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

I need to replace the fan blades on a Kirby Heritage II, Model 2HD, vacuum cleaner. How do I remove the drive shaft that the fan is mounted on? Thanks, Robert Croft


... Vacuums

I have a kenmore vaccum i order a new part need help in removing the old part.


... Kenmore Vacuums

I need to know how to remove and replace the filter on my Sebo Essential Gq vacuum.


There are two filters that need replaced, first one is inside the bag container it just pulls strait out and a bar will drop down to protect the vacuum from being used without the filter. just lift the bar up and slide the new filter in. next one is ... Sebo Vacuums

Hi I need to know how to remove the handle from the hose on a tristar vacuum. thanks, Hartley


... Tristar Vacuums

I need to know how to disassemble the power head for my pet vac. the brush no longer rotates, and it severely limits the quality of vaccuming. we have dogs, so it's really important for this thing to work at it's best!


... Euro-Pro Shark 18Volt Pet Perfect II Cordless Handheld Vacuum Cleaner

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]


The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

I need to know how to clean the hoses on a rainbow e series vaccum


Take the hoses completely off and then pour water down them. ... Vacuums

I have the bissell carpet shampooer, I need to remove the brushes to clean it but don't know how


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Poor suction-need to know how to remove & clean filter under canister of Hoover Wind Tunnel Mach 4.7 Twin Chamber System.


I assume this is a Hoover Bagless, if poor suction, the hose or dirt inlet by the brush roll may have a clog. The filter inside the dirt container may need replacement. Some had a screw to take out to remove the cover for the filter, the one under ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0900 seconds