Having problems with your Kirby Vacuums ?
New roller brush for g4a
\015 How much is a new roller brush for a G4A vacuum cleaner please.\015
Usually between $24-$30 depending on where you look.Shop around a little.Any vac shop should have them.
Repair Help & Product Troubleshooting for Kirby Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
New roller brush for g4a
Usually between $24-$30 depending on where you look.Shop around a little.Any vac shop should have them. ... Kirby Vacuums
Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?
The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum
Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?
I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
I placed the new belt on the brush roller like i was suppose to, but brush roller will not turn forward or backward. What am I doing wrong?
Most likely the roller is frozen due to dirt and debris.\015\012Follow the instructions to remove the belt and roller.\015\012Clean the roller as best you can and at each end where the hard rubber holders are located. Add some WD40 between the brush ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.
Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums
My dirt devil breeze was rattling while on. I found that the one end of the brush roller had shifted off the sqaure ends. Is it bent inside? Can it be repaired or do I need a new brush roller
The ends are fastened to each end of a shaft that passes through the roller. If the brush has shifted, perhaps the nuts or other fasteners have loosened. You can try to tighten the nuts but be carefaul to avoid tightening too much, causing the roller ... Dirt Devil Breeze Bagless VacuumVacuum
I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?
THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum
My oreck roller brush does not turn, belt is new and attached properly help
... Oreck Vacuums
Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.
You need to replace the belt. Replacement Vacuum Belts ... Vacuums
My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.
Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum
I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the
Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums
When we changed the belt the new belt broke right away and the brush roller wouldn't spin. My husband cleaned off the roller and got it moving slowly again, but when we went to re-attach everythin
The thing you call wheels are actually called roller bearings that fit at both ends of the brush-roll there probably seized up you can get a new brush-roll with bearings from the link below. ... Dirt Devil Breeze Bagged Upright
No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.
Generally, the problem is that the belt is not running the brushes. This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed. This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt
... Bissell 21K3 CleanView Helix Bagless Upright Vacuum
THE ROLLER BRUSH WILL NOT TURN. I PUT ON A NEW BELT AND IT BROKE IMMEDIATELY. THE ROD THAT HOLDS THE BELT IS MOVING BUT THE BRUSH IS NOT MOVING.
Apparently something is binding the brush, keeping it from turning. Remove any string, hair, etc., that is wrapped around the brush. Removing the brush is the easiest way to do this, then cut the material through at one point.\015\012While th ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum
Eureka Boss 4870 -Brush roller won't turn on carpet and turns when its not supposed to (with handle in upright postion). New belt had burning rubber smell right away.
Need new roller brush ***. and belts FM741B - Fantom Vacums FM741 Twister Bagless Upright Vacuum
... Fantom Vacums FM741 Twister Bagless Upright Vacuum
I replaced the belt already, cleaned the roller brushes well & put it all back together then the new belt broke too
Is the brush roll spining if not the belt is slipping and over heating and snaping ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]
Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Bought a Kenmore Progressive canister vacuum at a garage sale that looked in better than average condition, filters clean, new bag, all accessories intact, some debris in roller brush. problem is no suction when turned on. There does not appear to be any obstruction in hose. did not have manual
Hello,Carnister vacuum cleaners are all built with the same principle in mind. A motor \015\012generates power which powers a vacuum which, in turn, creates suction to\015\012 lift debris. The most common areas of suction loss are within ... Kenmore 25512/ 25513 Progressive Canister Vacuum
The roller brush will not rotate even after replacing with new belt- the skinny one
My roller wouldn't turn and the problem was that the larger flat self propel belt had gotten stretched. I replaced it with a new belt and the roller works great now. So perhaps you need to replace that belt also. Hold it up to a new belt and see if ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums
My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.
The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums
Eureka victory upright has no suction.has new bag and hoses are clear. Filters are clean,brush roller works fine.
... Kenmore Vacuums
I have a Fantom, model # FM740; i believe that I need a new roller brush. Is that something that I could order
If you need to replace the front agitator brush, they are available from Fantom and are easy to replace. You may also want to order and replace the drive belt also.\015\012You can call 1-800-275-9251 ... Fantom Vacums Vacuums