Having problems with your Kirby Vacuums ?

How do I change inside

\015 How do I replace the paper vacuum bag of a kirby next genaration vacuumcleaner?\015

Answers :

It should just be a matter of unzipping the cloth bag,and turning the cardboard backing on the paper bag slightly to one side,and pulling off.The cardboard backing on the new bag has notches that align with the fill tube to reduce slipping off when using.
Repair Help & Product Troubleshooting for Kirby Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance

Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

Dyson dco5 Pulled the unit too hard to get extra flex. The plug is ok changed the fuse. I believe the cable has detached itself from the inside. How can i check the inside of the unit for cable damage

Hi.\015\012\015\012Try this site has manuals on replacing mains rewinder unit on Dc05.\015\012http://dysonmanuals.llc.nu/\015\012\015\012Chris.. ... Vacuums

I have a fantom power pet model #fm722c how do i get inside to change the belt or remove the dirt from inside as well as the vacuum is not sucking the air thank you gail glandon

I have just cleaned out my filter and now it does'nt go back together?????Please help asap. It is a power/pet model ... Vacuums

Vacuum cleaner hi.this is 10 yrs old and not overly worked.bags are changed regularly and the micro filter has been changed at least three times over ten years.it goes well for about 2o minutes then loses power with not much "suck"after that.sometimes shutting down completely,because of overheating i presume,or just carries on at a much lower'"suck".have tied shaking bag inside but no luck.any suggestions out there or can you tell me the agents support office for new zealand[auckland].many thank

What brand vacuum is it? ... Vacuums

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat

It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

I need to change the belt. How do I get it off inside the vac.

Turn the vacuum over so you are looking at the brush.Remove the screws and that plate will come off.The belt fits on the brush,in a groove.The other end of the belt fits on a small wheel about 6 inches back,form the groove on the brush.There may be ... Dirt Devil Vacuums

I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.

Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums

I have a sanyo performaX 900W UPRIGHT and in the last week i have not been able to get it to work anymore, ive tried different outlets and nothing at all happens, this occured just after i changed the bag Can you please guide me in how to fix this problem? does the vacuum have a hidden button inside somewhere?

... Sanyo Permax SC-A114 Bagged Upright Vacuum

One day I was vacuuming and it sounded like something went up inside somewhere and the motor, I assume,..... is frozen ..all it does is hum when I turn it on! I have changed the belt, filter and checked and cleaned all hoses... what could this be? THANK YOU, Gail

It's likely something got into the fan, is stuck there, is preventing the fan from turning, and so prevents the motor running. There's a good possibility the motor burned out because of this. If there's a strong smell of burning metal, this is prob ... Hoover Elite Rewind Bagless Upright VacuumVacuum

I am trying to change the belt on a hoover legacy dirt finder. I cannot figure out how to get to the inside pully where the belt hooks

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=733898\015\012Generic problem for all Vacuums\015\012I am trying to change\015\012Posted by fuzzyplus1 ... Vacuums

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ

I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

My kirby sentra won't **** up anything. I've changed heads and bags to see if something was stuck inside but couldn't find anything.

Your inferance proves that the fault could be with the vacuum pump. Since the rest has been checked and there is a drastic reduction of the suction rate of the pump, I think the motor must be checked. Please remove to see if there is accumulation of ... Kirby G6 Bagged Upright Vacuum

How do I change inside

It should just be a matter of unzipping the cloth bag,and turning the cardboard backing on the paper bag slightly to one side,and pulling off.The cardboard backing on the new bag has notches that align with the fill tube to reduce slipping off when u ... Kirby Vacuums

I just notice when I went to change bag in my Kirby G4 that the whose inside was split open, which made all the dust fill up in the bag. How do I get a replacement part for this and what is that part called. Do I need to buy the whole outer bag?

You do not need a whole bag. The bag fill tube is replaceable. can be temp fixed with duct tape and new one installed at home. vacuum inside with another vac and you will be set to replace ... Kirby G4 Bagged Upright Vacuum

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.

It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

My hoover is broken, the hooze doesnt **** the dirt.I emptied the bag inside, there is nothing stuck in it.I think the hooze needs to be changed, where can I do it in Dublin?

You might check to see if the hose or the dirt inlet by the brush roll for a clog. Is the brush roll turning while you vacuum? If not, you may need a new belt. They stretch after awhile and turn the brush roll under load. ... Vacuums

Need help in changing the blade on inside of case housing for a old G6 type vac 15 plus yr old. how do i replace plastic blade.

This guide should make it easy for you!!!\015\012\015\012http://reviews.ebay.com/KIRBY-VACUUM ... Kirby G6 Bagged Upright Vacuum

How do I change the belt on my KIRBY CLASSIC OMEGA 1 CB ?

... Vacuums

It change the sounds while vacuuming

Its blocked ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do I get inside to replace u belt ?

Remove the three philips screws holding the yellow cover on the base. It will lift off, exposing the roller bar and belt. There are further instructions for belt change on a label inside. ... Vacuums

Chain tensioner Is it possible to change the chain tensioner of the Husqvarna 240 to a tool less chain tensioner or at least to the chain tensioner where the adjustment screw is accessed from the side not from the front. The problem is that there is a little plastic part that breaks rendering the chain tensioner useless. I have changed it twice and it keeps breaking. To change it you have to change the whole part that covers the break and chain mechanism.

... Husqvarna DMS 240 Core Rig - DMS 240 w/ Vacuum Pump

I hve a lacrosse satellite clock (battery driven). It hasn't changed with the spring time change and has not ability to change later than the EST. Will it eventually change??

Replace the battery from the clock and check.if the battery is gone weak it will not help the clock to change time.\015\012check out with new battery and see.\015\012keep updated.this will help.thanks. ... Vacuums

Hoover encore supreme belt change

... Vacuums

How to change belt on Dirt Devil Model 2003 can vac sweeper

I found out that the Royal Mfg. Co. used the same schematic from this model to make newer models which had a belt, however, this older model that I have does not have a belt drive. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0262 seconds