Having problems with your LG Kompressor Upright Vertical Cyclone Vacuum ?

On the back of my lg kompressor vacuum below the retractable cord is a suction plug that keeps sucking in when the vacuum is turned on it is supposed to stay out the increase suction. what is the solution for this problem.

Answers :

Remove the hose fitting on the lower back of the vacuum and you will probably find a large amount of debris lodged in the hose. That hose leads to an opening right behind the main roller brush. If you remove the brush, it is easier to remove any clogs that are inside the hose. Once you have checked that there is no clogs in that hose reconnect the hose and the brush. You should then remove all three filters and wash only the two filters inside the canister. The third filter is a HEPA filter located in a compartment on the lower front side of the vacuum. Make sure you do not wash the HEPA filter.Clean it by tapping it inside a trash can outside the house since a lot of dust will come out of it. Once the other two filters are dry, put them back inside the canister and also jake sure that the canister is empty and clean.
I've noticed the same problem. I put a cork in it and the suction improved, but I'm worried about overheaing the engine. Did you ever find out why the hole is there, and what to do about it?
Repair Help & Product Troubleshooting for LG Kompressor Upright Vertical Cyclone Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On the back of my lg kompressor vacuum below the retractable cord is a suction plug that keeps sucking in when the vacuum is turned on it is supposed to stay out the increase suction. what is the solution for this problem.

Remove the hose fitting on the lower back of the vacuum and you will probably find a large amount of debris lodged in the hose. That hose leads to an opening right behind the main roller brush. If you remove the brush, it is easier to remove any clog ... LG Kompressor Upright Vertical Cyclone Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.

Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Blue Moon S658 Miele vacuum problem where suction cuts off. The power light stays on. Sometimes I lose full suction, and other times I just lose partial suction. This shows on the handle by going from 1000 to 400, or nothing. Any thoughts on what this could be?

This is a problem with the circuit board in the SES-125 hose. If you replace the hose, this problem will stop. Unfortunately this is the only solution to this problem. \015\012\015\012-R ... Miele Blue Moon Bagged Canister Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.

I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

We have a Bissell Power Clean vacuum, Model# 92L3P. A few days ago the vacuum started revving extremely high. We still have suction, but the RPMs sound like they're through the roof. At first the problem was sporadic, but now it's consistent every time the vacuum is turned on.

... Bissell Vacuums

I have an Oreck canister vacuum, it says fc1000 on the bottom sticker, it's red. My problem is that the suction in it works perfectly, the belt is ok, and the roller can turn, but the motor doesnt turn it when I turn on the power.

... Vacuums

I have a Nutone CV-450. When the unit is turned on the motor makes a high pitched whining sound. The suction seems like it is reduced and there is a burning rubber smell coming from the unit. Suction at the unit itself is also reduced. Any ideas about the cause of the problem and the solution?

... Broan-NuTone CV450 Central Bagged Central System Vacuum

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.

You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

I received my dirt devil canister vacuum - vision pet for Christmas and have only used it several times. I am having trouble with it not suctioning very well. I have the max suctioning turned all the way up. It hardly picks up anything at all now. I can't seem to find my instruction manual. What's the problem?

Change out the bag. Check the internal air passages for blockage. Check air flow without the bag and pick--up hose in place--should be quite forceful. Attach the bag and try again. If ok, attach the hose and try again. At some point, you should find ... Vacuums

No suction I have a similar problem - volta vortex bagless vacuum will not ****. Worked for 1 job then quit sucking, I have had the heads replaced, then the barrel - 2 months later same problem. I push the power lever to max - 10 seconds later it turns itself down and doesn't work properly. I am over it, now looking for refund

Hi there SmartAlec from NelsonVacuums.com.au here. The problem is going to be the filter. THis kind of vacuum basically replaces the bag with a simple filter and the vacuum ... Vacuums

Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?

Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum

I have a hoover Core vacuum. The problem is that the blue light flashes (as normal) when it is plugged in and the power is turned on and the blue light stays on (as normal) when you turn it on at the button but it makes no noise and doesnt work. All of the filters are clean. Can you help please?

... Hoover Vacuums

I just purchased the hoover steam vac model F5853-900 from a garage sale and everything seems to be working well except i dont see any steam coming out from anywhere and the water in the vacuum stays cold. is there supposed to actually be a steamer inside this vacuum? if so, is there a button i need to turn on for the steamer to work? thank you so much for the help!

... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Hi, My problem is that I'm getting hardley any suction when I vacuum. The machine has a new bag and the rollers are turning, just no suction. Thanks!

Take out the brushroller and check the hole where the dirt goes into the machine for clogs.\015\012\015\012Marci ... Hoover Vacuums

Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.

Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum

My vacuum makes a wierd sucking and blocking sound when turned on and when you put the extension tube on the suction decreases...but when just the wand handloe is on the suction is excellent...we replaced the barrel thinking it was broken but that hasnt fixed the problem

You did not list the make and model of your unit, so it is difficult to hunt for problems.\015\012\015\012Check to see if any of the tube vents might be open. They should be closed when in use.\015\012Also check to see there are no holes in th ... Vacuums

Bought a Kenmore Progressive canister vacuum at a garage sale that looked in better than average condition, filters clean, new bag, all accessories intact, some debris in roller brush. problem is no suction when turned on. There does not appear to be any obstruction in hose. did not have manual

Hello,Carnister vacuum cleaners are all built with the same principle in mind. A motor \015\012generates power which powers a vacuum which, in turn, creates suction to\015\012 lift debris. The most common areas of suction loss are within ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Oreck XL vacuum cleaner disposable bag does not stay attached. I had my husband put it on and again it came off. The cloth bag is always full of dust and suction is lost. What is the solution?

... Oreck XL Ultra Bagged Upright Vacuum

I have a Hoover SteamVac Duo Deep Cleaner, model #F5520. The brushes won't turn and it won't release solution. There IS suction. Any ideas what could be the problem?

... Hoover F5520 SteamVac Duo Upright Wet Washer

The wand will not stand up on its own when attached to the vacuum head. I had earlier models which did not have the adjustable height and this was not a problem--I simply turned the wand to the side. But I cannot do it on with this wand. Any solutions?

Hello. There is a small part on that wand which enables it to stand up on it's own. It sounds like yours is worn or broken. Take it to your local vacuum repair store and they will have you back up and standing in no time. The part is about ten do ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hi there, I have an excellent Electrolux (but older) Diplomat LX model which stops when the bag is supposedly full. It''s not full however, but merely 1/4 to 1/3 full. I'd like to reduce the "sensitivity" of the sensor or turn it off altogether. I don't run my vacuum with a full bag, but there's a limit. Please tell me how to address this problem. Thanks very much. Pierre

... Electrolux Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1155 seconds