Having problems with your Lindhaus Diamante 300 Upright Vacuum ?

Lindhaus- replace hose to handle_ hose came out - difficult to screw back in-


Answers :

Repair Help & Product Troubleshooting for Lindhaus Diamante 300 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lindhaus- replace hose to handle_ hose came out - difficult to screw back in-


... Lindhaus Diamante 300 Upright Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.


Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Sister borrowed vacuum. When it came back it was missing a hose from canister to upright part. Where do I find a replacement?


If you go to www.dyson.com , Online Store, Parts & Accessories, DC14 Animal, the "internal hose" sells for $8.99. The Part# is 904219-05. This short hose is located on the under ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

DC25 telescoping handle does not seat tightly. When pulling the vac back it unseats about 2 inches. This prevents the hose from engaging securely in the base and suction is affected. Do I need to replace the clear wand release catch? I've only had the vac about a year and am surprised it would wear out so quickly.


... Dyson DC25 Vacuum

Can the damaged hose 8 inces from handle be cut then replace hose


If the hose is non-wired then you can fix this yourself. When you Plug the cuff into your wall inlet does the vacuum turn on automatically? If so then you should be able to trim the hose with no ill effects other than losing eight inches of cleaning ... Electrolux Central Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!


Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

Our dustbuster (dont' have model number with me-sorry) won't turn off when I pull back on the switch handle. I disassembled the unit and realize that the tab on the switch handle that pulls back on the internal switch handle to turn it off is not strong enough for its simple task. Does B&D have a proper replacement part?


If you can provide a model number, I can check availability of the switch and can either order it for you, or supply the B&D part number and you can order it from most local vacuum shops in your area or from Black & Decker direct online: ... Black & Decker 15.6 Volt DustBuster Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

I have an Elextrolux Discovery Advantage(upright) . I need to replace the lower hose. Unfortunately the hose comes out of the roller/feeder area fine but I believe it is held in with a screw in the canaster area. My question is this: How can i open the Canaster area - ther is no isable screws


It's simply screwed into the tank. Simply unscrew in a clock-wise direction to remove. To install the new hose, screw in in a counter-clockwise direction. This is opposite the direction normally used for regular screws. \015\012You don't ne ... Electrolux Vacuums

My handle won't go back up after an extended vacuuming session during which I used the hand/broom/animal hair attachments several times, thus pulling the hose out/putting it back in, starting/ stopping, and suddenly no matter what I do short of forcing it (and even if I try forcing it a bit) I can't raise the handle to put it away.


Do you know what model number Dyson you have? Is it the ball style one? Just find a similar product here on this page and let me know what model number is closest: ... Dyson Vacuums

Bissell 35962 Cleanview Bagless Revolution Upright Vacuum hose is clogged with sock where hose meets handle attachment. Attempted to use broom handle to push back through suction opening. Sock is compacted. Any home repair advice?


If you have access to a small sink "snake" used to clear clogs in sinks, you might be able to use it to "snag" the sock and pull it out.\015\012Needs to be a metal sewer snake so that you can tug on it if and when it snags the sock. ... Bissell 35962 Cleanview Bagless Revolution UprightVacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hi. Bought a M3888-3 Royalcylinder vacuum from Lidl. Lost manual that came with it. Only had it 4 mths. Need new hose. Plastic hose has snapped near whereit attaches to metal hose. Can I get a replacement hose from somewhere in U.K.? I know the vacuum is from Germany.


... Royal Vacuums

How do I replace the handle on Electrolux 1205 powered hose?


... Electrolux Canister Vacuum Cleaner Wand Silverado, 1205

I have a Kenmore Progressive Canister Model # 29612992. I was replacing the sweeper bag, when I opened the lip, the plastic arms was pull out of joint and will not close. I removed the 2 screws under the lid to put back it in place but there I can't remove the plastic molding because there are still screws holding somewhere. Are there tabs instead of screws still hold the molding?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

My BROAN CV-110 hose with the rug beater only works if I turn it on from the base unit. Shouldn't it turn on when I plug the hose into the wall recepticle? Do I need to replace the hardware at the end of this hose and if so, where would I purchase that? This central vac came in a house I just purchased. Thanks for any help. Sherry


... Broan-NuTone CV450 Central Bagged Central System Vacuum

Can the suction hose fitting where it attatches to the base be reattatched, it has torn away from the snap-on fitting or do I have to replace the complete hose unit, the model is F5878-900.The existing hose is screwed into this fitting and glued.


You must replace the whole hose unit. its not very cheap either ... Hoover F5878-900 SteamVac Upright Vacuum

The small button on the hose handle is missing, I need a replacement


... Euro-Pro EP923 Canister Steam Vacuum

Took handle off to use hose now can't put it back together


... Dyson DC25 All Floors Bagless Upright Vacuum

The screw that holds the handle to the top of the canister came completely loose. How do I get to it to reattach?


Buy a epoxy cement and fill the hole with it, then drill a hole a little smaller than the screw, and finally insert screw. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0821 seconds