Having problems with your Lindhaus HF6-12 Canister Vacuum ?

Wire came loose, can't figure out where it belongs

\015 I have a lindhaus healthcare pro and we vacuumed liquid that had been sitting in someone's carpet for sometime. I completely disassembled the vacuum, to clean and dry it. While removing the foam bag, enclosing the motor, I pulled loose a wire, and can find no apparent spot to replace it. The end is frayed, not enclosed in a clip. Thank you for your assistance!\015

Answers :

Maybe one of the wires that leads to the power head?
Repair Help & Product Troubleshooting for Lindhaus HF6-12 Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wire came loose, can't figure out where it belongs


Maybe one of the wires that leads to the power head? ... Lindhaus HF6-12 Canister Vacuum

Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help


Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o


Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I need to wire the switch to my coleman 2234 push button 12v water pump in my camper trailer. it is wired to the battery now with the "red" connected through a small fuse. i just cant figure out where to wire the on/off switch to.


Hi there. When connecting a switch, it is important to remember that a switch will only "break" the positive (+) circuit, while the neutral wire will go directly to the battery. So, basically split the red wire coming from your pump and connect the s ... Coleman Vacuums

I have a Fantom, Cyclone XT vaccum and while attempting to clear a blockage the wires inadvertantly came loose from the power on/off selector switch located on the top front of the unit and I need to reinstall the wiring in the proper order


... Fantom Vacums Cyclone XT Upright Vacuum

I need a wiring diagram for the shark mop a wire came loose but can't find out where it goes ???


... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Loosing suction I am loosing suction on my vacuum. I have only had it for about 6 months and cant figure out what is wrong. Can you help?


Well you did not state what model and brand this is, but usually if the hose or the dirt inlet by the brush roll gets clogged, then you lose suction. If you can't figure it out, usually there is a year warranty, take it in for warranty service. ... Vacuums

Help ok the diagram is helpful but i have a black wire that came loose from somewhere it has a little prong on it does it click back in opposite from the white let me know please


I am not sure what exactly you are referring to but I think that it may be a motor lead. See pictures below (shown is white but second wire to the motor is black) ... Rainbow E series Canister Wet/Dry Vacuum

I have a dyson DC14. the forward lock came out and I cant figure out how to get it back in. Please help!


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The extesion peice on my dyson ball dc25 will not detach from the vacuume to extend. I am going to loose my mind if i cant figure it out!


Use electric ... Dyson Ball DC24 Bagless Upright Vacuum

I was changing the pump belt now i have this lever like thing w a spring on it that i cant figure out where it goes or how it came off


Could it be the handle lock lever ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

There seems to be a wheel that holds tension to the belt which came off. Now the belt spins and makes a grinding noise. I cant figure out how to get to the belt? Any one have advice?


I can help you a lot further if you can send me a picture of the bottom side of the vacuum. My email is [email protected] Once I see a picture this will help me tell you how to fix it. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My G7D kirby vac was accidently dropped and the D & N lever came out of the machine. When I put the lever back in the hole it belongs in it is very loose and it doesn't switch from D or N.


The drive/ neutral pedal assembly must be replaced. This part is pressed together and cannot be repaired. A new assembly is about $17-$20. The power drive unit must be removed from the machine. ... Kirby Ultimate G Bagged Upright Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

TOOK MY ELECTROLUX EPIC 6500 CANISTER MODEL 1762 APART TO REPLACE CORD REWINDER. TO MAKE A LONG STORY SHORT,MOST OF THE WIRES CAMES OFF OF HEIR CONNECTIONS. NOW CAN'T FIGURE OUT WHERE THEY GO WITHOUT A SCHMATIC. CAN ANYBODY HELP. THANKS CATHY


Hi,\015\012\015\012I will try to find a service manual for you. ... Vacuums

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?


You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Wires came undone and I need to reconnect them


Can you take a picture and post what you have to work with. I can help you but I haven't worked on one for a year or two so I don't remember the colors, etc. ... Sharp Twin Energy EC-T4660 Vacuum

Loose wire Been tugged causing loose wire at handle end of flex


Needs new cable 20.00 for replacement 0800 294 4692 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t


... Vacuums

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

Hi I have the Ambassador 337 model. I had to rewire the on off wiring due to the "N" wire rubbing through & breaking. I have it all together again although a piece of wire in the shape of a "V", with a bend each side of it has dropped out & I don't know where it came from!!!! Please send me diagram of this model so that I know where it goes. Cheers Ian.


... Electrolux Vacuums

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.


Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

Brown wire came off where does it go. electrolux guardian power nozzel


Send me picture of the wires and connection location, then I'll be able to help ... Electrolux Guardian Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0309 seconds